[TechAssist] Re: RCA D52W20YX1 Convergence
- From: "Valley TV" <valleytv@xxxxxxxxx>
- To: techassist@xxxxxxxxxxxxx
- Date: Thu, 02 Feb 2006 09:57:47 -0500
Thanks for the tip Jim but I actually did try the
green geometry. The problem- I did not have
the template so I am not sure my adjustments were
exactly correct so THAT could be the problem.
Gary
Valley TV Drums, Pa office
> ----- Original Message -----
> From: "Jim Myers" <jr.myers@xxxxxxxxxxx>
> To: techassist@xxxxxxxxxxxxx
> Subject: [TechAssist] Re: RCA D52W20YX1 Convergence
> Date: Thu, 02 Feb 2006 09:28:42 -0500
>=20
>=20
> You probably have some geometry adjustment that is slightly out, do the
> geometry alignment first then see if the auto convergence works.
>=20
> The Old Master Technician
> ********************************
> Since 1972 *
> Jim Myers *
> Telrad Electronics *
> Fort Wayne Indiana *
> ********************************
>=20
>=20
> Valley TV wrote:
> > Hi Everyone.. "Another" week..
> > I encountered a problem with a D52W20YX1 (ATC221) that
> > I have not run into before. Poor convergence in the
> > bottom left side was apparent as I walked in the door.
> > I expected to find a problem on the convergence circuit
> > board and was surprised that everything tested fine.=3D20
> > I accessed the factory menu and found the green was out
> > and was really surprised that it adjusted perfectly.
> > I saved my settings & then ran the sensor setup & was
> > once again surprised that the screen flashed RED
> > instead of green when it completed. I thought maybe
> > my memory was wrong & red was the color the screen
> > DID flash at the end but... I exited the factory menu
> > & shut the set off. Convergence was perfect when=3D20
> > restarted & I left it heat up 15 minutes then started
> > the customer autoconvergence feature.. Hmmm. Unit only
> > started the procedure for 8-9 seconds and quit.. Seemed
> > to do it on red & did no "damage" to the convergence but
> > customer was not happy. I ran it a few times and SOMETIMES
> > it went through the whole procedure but usually stopped
> > in the first 8 seconds.. I'm frazzled.. Any thoughts??
> >
> > TIA!!!!
> >
> > Gary
> > Valley TV
> > Drums, PA office
> >
> >
> > --=3D20
> > ___________________________________________________
> > Play 100s of games for FREE! http://games.mail.com/
> >
> > -----------------------------------------------------------------------=
------
> > This Email List is accessible to the general public through=20
> > search engines. Remove: http://www.tech-assist.org/remove.htm
> > Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=3Dset%20techassist%20=
vacation
> > Lost Password: http://www.tech-assist.org and select "Login Problems?".
> > Email Archives: //www.freelists.org/archives/techassist/
> >
> -------------------------------------------------------------------------=
----
> This Email List is accessible to the general public through=20
> search engines. Remove: http://www.tech-assist.org/remove.htm
> Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=3Dset%20techassist%20va=
cation
> Lost Password: http://www.tech-assist.org and select "Login Problems?".
> Email Archives: //www.freelists.org/archives/techassist/
>
Valley TV
Drums, PA office
--=20
___________________________________________________
Play 100s of games for FREE! http://games.mail.com/
-----------------------------------------------------------------------------
This Email List is accessible to the general public through search engines.
Remove: http://www.tech-assist.org/remove.htm
Set Vacation mailto:ecartis@xxxxxxxxxxxxx?subject=set%20techassist%20vacation
Lost Password: http://www.tech-assist.org and select "Login Problems?".
Email Archives: //www.freelists.org/archives/techassist/
Other related posts: