Memory save is to shut set off with "KEY BOARD" Adolph Gower Cordova TV 10275 Old Placerville Rd. # 5 Sacramento, Ca. 95827 Phone (916)-363-6565 Fax (916)-363-7623 agower@xxxxxxxxxxxxx agower@xxxxxxxxxxxxx agower@xxxxxxxxxxxxx ----- Original Message ----- From: "Leonard G. Caillouet" <lcaillo@xxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, May 15, 2002 1:13 PM Subject: [TechAssist] Re: Magnavox FP4620W101 PTV705AH01 convergence menu > > Thanks Joe, Bob. > > I must have a problem with this one. I sent the convergence module to > Tri-State because it was distorted and I could not adjust it at all. Now I > can adjust it but it will not hold memory. Is the memory for convergence on > this module? I suspect it is. Is there some mode in the service menus that > prevents saving the data? This set was apparently serviced by someone else > before I got it so I don't know what might have been done to it. Any > suggestions would be appreciated before I send the module back to Tri-State. > > Leonard G. Caillouet > Service Manager > Electronics World > Gainesville, FL > 352-332-5608 > 352-332-5668 (fax) > > ----- Original Message ----- > From: "Joe Prokup" <pro501@xxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Wednesday, May 15, 2002 3:16 PM > Subject: [TechAssist] Re: Magnavox FP4620W101 PTV705AH01 convergence menu > > > > > > Leonard: > > Convergence touch-up mode 06-25-97 Menu > > That should take you to the opening menu. > > From there you can do green, red to green, blue to green,green to red, or > > green to blue. > > If you do not have the template its best to just do the touch-up. > > I have the Service Manual in the shop if you get lost. > > Joe Prokup > > PRO-ELECTRONICS > > Spring Valley, IL > > PH 815-663-3005 FAX 815-371-0190 > > pro501@xxxxxxxxxxxxx > > ----- Original Message ----- > > From: "Leonard G. Caillouet" <lcaillo@xxxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Sent: Wednesday, May 15, 2002 11:50 AM > > Subject: [TechAssist] Magnavox FP4620W101 PTV705AH01 convergence menu > > > > > > > > > > Could someone tell me how to access the convergence menu for this set. > I > > > can get into the service menu with 0,6,2,5,9,6,menu but there are no > > dynamic > > > convergence settings here, only static convergence. > > > > > > Leonard G. Caillouet > > > Service Manager > > > Electronics World > > > Gainesville, FL > > > 352-332-5608 > > > 352-332-5668 (fax) > > > > > > > > > ------------------------------------------ > > > To REMOVE your email address, click here: > > > http://www.tech-assist.org/unsubb.html > > > ------------------------------------------ > > > ***NEW*** Tips Added Instantly!!!*** > > > Submit Repair Tips here: > > > http://www.tech-assist.org/secure/tip/ > > > > ------------------------------------------ > > To REMOVE your email address, click here: > > http://www.tech-assist.org/unsubb.html > > ------------------------------------------ > > ***NEW*** Tips Added Instantly!!!*** > > Submit Repair Tips here: > > http://www.tech-assist.org/secure/tip/ > > ------------------------------------------ > To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html > ------------------------------------------ > ***NEW*** Tips Added Instantly!!!*** > Submit Repair Tips here: > http://www.tech-assist.org/secure/tip/ > ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html ------------------------------------------ ***NEW*** Tips Added Instantly!!!*** Submit Repair Tips here: http://www.tech-assist.org/secure/tip/