Thanks Peter I ordered both volumes today. Regards Ralph W. Lambrecht On 1/15/05 1:44 AM, "Peter De Smidt" <pdesmidt@xxxxxxx> wrote: > _Petersen's Photo Equipment You Can Make_, 1973, ISBN 0-8227-0020-04, > edited by Parry Yob has 80 pages of DIY photo gear. Here are the projects: > > 1. How to build a camera dolly. > > This project is for a sturdy counter-balanced studio stand suitable for > 4x5 and smaller cameras. It looks pretty good. If I had space to store > it, I'd build this one. It's fairly complex. You'd probably want a jig > saw, circular saw and drill for this project, although it would best be > made with lumber that's been through a jointer, planer, and table saw. > > 2. How to build a light boom. > > This project is for a wooden, counter-balanced light boom. It looks > pretty good, although it doesn't break down as small as professional units. > > 3. How to build a soft box. > > This ones for making a 2ft x 4ft rigid soft box and stand with tungsten > light bulbs. It's fairly complex and quite bulky. I prefer professional > fabric boxes with strobes. > > 4. How to build reflectors. > > There are a bunch of reflector here. One involves making a bunch of > triangles of rigid white mat board with roughly 7" sides. These are > taped and glued into a hemispherical reflector. These are bulky and > seem like to much effort for what you get. Foam core, white rigid foam, > and collapsible reflectors seem like betters solutions. > > 5. How to build a background stand. > > This project is for a sturdy background stand made out of construction > lumber and plywood. It would do the job, but it's pretty bulky. It > would work well in a permanent location. > > 6. How to build a posing stand. > > With a few minutes consideration you could probably come up with a > better bench. > > 7. How to build a 10 minute film dryer. > > This is a tall wooden box with forced hot air. I prefer air drying my > film at ambient temperature. > > 8. How to build a darkroom timer. > > This is for a 12" square timer, much like the old Graylab. I can't > believe that this would be a worthwhile project. Get a StopClock and be > done with it. F-stop printing really is the way to go. > > 9. How to build a solution warming cabinet. > > This is a lot of work. A simple heated water bath with an aquarium pump > and heater works just as well, and it doesn't take up as much space. > > 10. How to build a vacuum easel. > > This is a simple, straight-forward project. > > 11. How to build a print-washer. > > This involves fiberglassing a box and putting in various PVC fittings. > I built a better washer out of acrylic with a scoring knife, aquarium > caulk, and strong packing tape 10 years ago. It's held up fine, although > I now use it as the water bath element of a DIY slot processor for RA4. > For my money, a Versalab washer is hard to beat. > > 12. How to build a matte print dryer. > > Moderately complex. This involves cone heater elements that screw into > light bulb sockets. I don't know where one would get these. It looks > like a fire hazard. > > 13. How to build a mat board cutter. > > My Alto easy mat is more versatile, and it didn't cost very much. > > 14. How to build a dry mount press. > > This is an advanced project. You have to have a rectangular pan made of > 20 gauge galvanized metal. It involves stringing nichrome wire in the > pan, and then pouring plaster of Paris into it. While presses are > expensive, finding a used one would seem to be a better option. > > -Peter De Smidt > > > ============================================================================== > =============================== > To unsubscribe from this list, go to www.freelists.org and logon to your > account (the same e-mail address and password you set-up when you subscribed,) > and unsubscribe from there. ============================================================================================================= To unsubscribe from this list, go to www.freelists.org and logon to your account (the same e-mail address and password you set-up when you subscribed,) and unsubscribe from there.