[modeleng] Re: No new topic ?
- From: Allen Messer <al_messer@xxxxxxxxx>
- To: modeleng@xxxxxxxxxxxxx
- Date: Mon, 26 Sep 2005 16:54:22 -0700 (PDT)
O.K. Thanks, Ron. What BA size(s) would you suggest
for a model cylinder that is 1-5/8" bore x 3" stroke?
Al Messer
--- Ron Head <ron.head@xxxxxxxxxxxxx> wrote:
> Hi Al
>
> No-one else has replied, so I'll bite.
>
> As far as British locos are concerned, the only
> place I've seen slotted
> screws is in the boiler cleading - usually around
> the backhead area where
> small pieces are joined together, or where feed pipe
> covers and the like are
> attached.
>
> Regards
> Ron
>
> ----- Original Message -----
> From: "Allen Messer" <al_messer@xxxxxxxxx>
> To: <modeleng@xxxxxxxxxxxxx>
> Sent: Monday, September 26, 2005 4:26 PM
> Subject: [modeleng] Re: No new topic ?
>
>
> > O.K. I have awakened from my Cold Medicine
> induced
> > stupor long enough to think of something to ask:
> > When, if ever, were slotted head screws used on
> full
> > sized prototype steam engines, and where would it
> be
> > appropriate to use them on a scale model?
> >
> > Al Messer
> >
> > --- lanchhale@xxxxxxxxxxxxxxxx wrote:
> >
> >> Dave
> >>
> >> I was lucky enough to be offered a drive of the
> >> Royal Scot after you left.
> >> It was beautiful but so large after the 1366,
> the
> >> dome was where her
> >> chimney is!!
> >>
> >> Just as we were about to load her up the weather
> >> broke & we got soaked,
> >> but after that drive albeit short it didnt really
> >> matter!!
> >>
> >> See you tomorrow.
> >>
> >> Cheers
> >>
> >> Adrian
> >>
> >> > Get well soon guys. I have been soooooo busy
> with
> >> my daughters birthday
> >> > party. We had a 71/4 GWR13XX, a 7 1/4 Scot, (A
> >> proper engine!!), a 7 1/4
> >> > Britania and a 5"Martin Evans B1, that was on
> the
> >> ground level. On the
> >> > raised level we had a 5"Brit and my 5" IoM
> Beyer
> >> peacock. A great day was
> >> > had by all, the older kids enjoyed it more me
> >> thinks!
> >> >
> >> > Thats all over now so back to the workshop to
> >> fettle my stationary engines
> >> > for Tues club night.
> >> >
> >> > Dave.
> >> > ----- Original Message -----
> >> > From: "Allen Messer" <al_messer@xxxxxxxxx>
> >> > To: <modeleng@xxxxxxxxxxxxx>
> >> > Sent: Sunday, September 25, 2005 1:47 AM
> >> > Subject: [modeleng] Re: No new topic ?
> >> >
> >> >
> >> > Well, I've felt too badly all day to even take
> off
> >> my
> >> > pajamas much less think of something, BUT, you
> >> just
> >> > wait until I'm rid of this snotty-nosed Cold!!
> >> >
> >> > Al Messer
> >> >
> >> > --- Pcx <pierre.courbouleix@xxxxxxxxxx> wrote:
> >> >
> >> >> Hi LIst,
> >> >> Still alive ? No new topic since 72 hours !
> >> >> PIerre
> >> >> MODEL ENGINEERING DISCUSSION LIST.
> >> >>
> >> >> To UNSUBSCRIBE from this list, send a blank
> email
> >> >> to,
> >> >> modeleng-request@xxxxxxxxxxxxx with the word
> >> >> "unsubscribe" in the subject line.
> >> >>
> >> >
> >> >
> >> >
> __________________________________________________
> >> > Do You Yahoo!?
> >> > Tired of spam? Yahoo! Mail has the best spam
> >> protection around
> >> > http://mail.yahoo.com
> >> > MODEL ENGINEERING DISCUSSION LIST.
> >> >
> >> > To UNSUBSCRIBE from this list, send a blank
> email
> >> to,
> >> > modeleng-request@xxxxxxxxxxxxx with the word
> >> "unsubscribe" in the subject
> >> > line.
> >> >
> >> >
> >> >
> >> > MODEL ENGINEERING DISCUSSION LIST.
> >> >
> >> > To UNSUBSCRIBE from this list, send a blank
> email
> >> to,
> >> > modeleng-request@xxxxxxxxxxxxx with the word
> >> "unsubscribe" in the subject
> >> > line.
> >> >
> >> >
> >>
> >>
> >> MODEL ENGINEERING DISCUSSION LIST.
> >>
> >> To UNSUBSCRIBE from this list, send a blank email
> >> to,
> >> modeleng-request@xxxxxxxxxxxxx with the word
> >> "unsubscribe" in the subject line.
> >>
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Tired of spam? Yahoo! Mail has the best spam
> protection around
> > http://mail.yahoo.com
> > MODEL ENGINEERING DISCUSSION LIST.
> >
> > To UNSUBSCRIBE from this list, send a blank email
> to,
> > modeleng-request@xxxxxxxxxxxxx with the word
> "unsubscribe" in the subject
> > line.
> >
> >
> > --
> > No virus found in this incoming message.
> > Checked by AVG Anti-Virus.
> > Version: 7.0.344 / Virus Database: 267.11.6/111 -
> Release Date: 23/09/2005
> >
> >
> MODEL ENGINEERING DISCUSSION LIST.
>
> To UNSUBSCRIBE from this list, send a blank email
> to,
> modeleng-request@xxxxxxxxxxxxx with the word
> "unsubscribe" in the subject line.
>
__________________________________
Yahoo! Mail - PC Magazine Editors' Choice 2005
http://mail.yahoo.com
MODEL ENGINEERING DISCUSSION LIST.
To UNSUBSCRIBE from this list, send a blank email to,
modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject line.
Other related posts:
