[modeleng] Re: Heinrici
- From: Chris Crosskey <chris.crosskey@xxxxxxxxx>
- To: "modeleng@xxxxxxxxxxxxx" <modeleng@xxxxxxxxxxxxx>
- Date: Tue, 15 Nov 2011 15:58:59 +0000
I think the trick will be to cover it in hard-board.... sounds like a cheap
solution certainly :-)
> -----Original Message-----
> From: modeleng-bounce@xxxxxxxxxxxxx [mailto:modeleng-
> bounce@xxxxxxxxxxxxx] On Behalf Of Barrie Purslow
> Sent: 15 November 2011 10:29
> To: modeleng@xxxxxxxxxxxxx
> Subject: [modeleng] Re: Heinrici
>
> Chris,
>
> You'll be sorreeeeee!
>
> Barrie
>
>
> ----- Original Message -----
> From: "Chris Crosskey" <chris.crosskey@xxxxxxxxx>
> To: <modeleng@xxxxxxxxxxxxx>
> Sent: Monday, November 14, 2011 2:21 PM
> Subject: [modeleng] Re: Heinrici
>
>
> > That's not very good news, I'm about to make one for my new workshed
> from
> > a [piece I got removing a double unit in the kitchen to accommodate
> the
> > chest freezer.....
> >
> > Chrisc
> >
> >
> >> -----Original Message-----
> >> From: modeleng-bounce@xxxxxxxxxxxxx [mailto:modeleng-
> >> bounce@xxxxxxxxxxxxx] On Behalf Of Barrie Purslow
> >> Sent: 13 November 2011 19:49
> >> To: modeleng@xxxxxxxxxxxxx
> >> Subject: [modeleng] Re: Heinrici
> >>
> >> Alan,
> >>
> >> It'll never fly!
> >>
> >> I made a new bench top recently using the same material as shown in
> >> your
> >> photo - what a disaster - small items just disappear the moment they
> >> touch
> >> the surface!
> >>
> >> Cheers,
> >>
> >> Barrie
> >>
> >>
> >> ----- Original Message -----
> >> From: "stepney" <alan@xxxxxxxxxxxxxxxx>
> >> To: <modeleng@xxxxxxxxxxxxx>
> >> Sent: Sunday, November 13, 2011 6:27 PM
> >> Subject: [modeleng] Re: Heinrici
> >>
> >>
> >> > Progress to date.
> >> >
> >> > http://www.alanstepney.info/he2s.jpg
> >> >
> >> > Back row, L to R:
> >> > Displacer (needs a clean), two flywheels, two bearing standards
> >> >
> >> > Main casting, crank pin, piston yoke, piston, power cylinder.
> >> >
> >> > Displacer con rod and shaft.
> >> >
> >> > At the front is a marked out piece of steel that will be the
> power
> >> > crankshaft.
> >> > I suspect that there was a casting for it, but I cant find it, so
> am
> >> > having to make one.
> >> >
> >> > All the other pins, bolts etc are made as are the cooling water
> >> > fittings. The latter still need the pipes, and I plan to have
> pumped
> >> > water, so will need to make a pump.
> >> >
> >> > The biggest item still to make is the "furnace" on which the
> engine
> >> > stands.
> >> >
> >> > MODEL ENGINEERING DISCUSSION LIST.
> >> >
> >> > To UNSUBSCRIBE from this list, send a blank email to,
> >> > modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the
> >> subject
> >> > line.
> >> >
> >>
> >> MODEL ENGINEERING DISCUSSION LIST.
> >>
> >> To UNSUBSCRIBE from this list, send a blank email to,
> >> modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the
> >> subject line.
> >
> >
> _______________________________________________________________________
> _
> > This e-mail, and any attachment, is confidential. If you have
> received it
> > in error, do not use or disclose the information in any way, notify
> me
> > immediately, and please delete it from your system.
> >
> _______________________________________________________________________
> _
> > MODEL ENGINEERING DISCUSSION LIST.
> >
> > To UNSUBSCRIBE from this list, send a blank email to,
> > modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the
> subject
> > line.
> >
>
> MODEL ENGINEERING DISCUSSION LIST.
>
> To UNSUBSCRIBE from this list, send a blank email to,
> modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the
> subject line.
________________________________________________________________________
This e-mail, and any attachment, is confidential. If you have received it in
error, do not use or disclose the information in any way, notify me
immediately, and please delete it from your system.
________________________________________________________________________
MODEL ENGINEERING DISCUSSION LIST.
To UNSUBSCRIBE from this list, send a blank email to,
modeleng-request@xxxxxxxxxxxxx with the word "unsubscribe" in the subject line.
Other related posts:
