You might want to make sure you have a NO RAT Property on your large power/gnd nets. That will slow you down as well. Tony Stanislao, Senior PCB Design Engineer Pannaway Technologies | v: 603.766.5129| e: stanislao_t@xxxxxxxxxxxx ========================================= -----Original Message----- From: Mike Finczak [mailto:mike@xxxxxxxxxxxxx] Sent: Tuesday, June 29, 2004 5:21 PM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: Allegro 15.1 Deleting Vias, very slow? Blake, Try identifying the DC nets in Allegro: click ---> Logic ---> Identify DC nets Enter the voltages for each DC net. e.g. GND = 0 V BGA3v3 = 3.3 v If that does not work, turn off the dynamic shape update until your finished adding the vias. Click ---> Shape ---> Global Dynamic Params Under the "Shape Fill" tab, toggle the "Dynamic Fill" to "Disabled". Regards, Mike Finczak CopperCAD Design www.CopperCAD.com 905-488-8958 -----Original Message----- From: Moore, Blake [mailto:Blake.Moore@xxxxxxxxxx] Sent: June 29, 2004 4:03 PM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Allegro 15.1 Deleting Vias, very slow? I have Allegro 15.1 on the Sun, We use a lot of active shapes, and have to add via's along a cline line, "stitching vias to gnd along signal path for noise etc.." When adding and or deleting vias, It is super slow, if you go to setup dwg options and turn off, online drcs and set shape fill to rough, that helps some, but it's still really slow, does anyone else have this problem? -----Original Message----- From: Kevin McCowan [mailto:kmccowan@xxxxxxxxxxxxxx] Sent: Tuesday, June 29, 2004 1:49 PM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: Deleting Vias That's probably it. That messes me up all of the time! It's so hard to debug, too. Kevin george.h.patrick@xxxxxxxxxxxxxx wrote: > > Thanks for the useful replies :) > > Once I had deleted the etch, deleted the via, and replaced all in > their new location, I couldn't duplicate the message I was getting and > the vias are acting normally. > > Who knows? Must have been the alignment of the moons of Jupiter or > something :) > > -- > /George Patrick/ ----------------------------------------------------------- To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or unsubscribe To view the archives of this list please login at //www.freelists.org. Our list name is icu-pcb-forum or go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx Want to post a job listing ? DON'T DO IT HERE! Better yet, join our jobs listing forum. SUBSCRIBE: icu-jobs-forum-subscribe@xxxxxxxxxx POST: icu-jobs-forum@xxxxxxxxxx ----------------------------------------------------------- ----------------------------------------------------------- To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or unsubscribe To view the archives of this list please login at //www.freelists.org. Our list name is icu-pcb-forum or go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx Want to post a job listing ? DON'T DO IT HERE! Better yet, join our jobs listing forum. SUBSCRIBE: icu-jobs-forum-subscribe@xxxxxxxxxx POST: icu-jobs-forum@xxxxxxxxxx ----------------------------------------------------------- ----------------------------------------------------------- To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or unsubscribe To view the archives of this list please login at //www.freelists.org. Our list name is icu-pcb-forum or go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx Want to post a job listing ? DON'T DO IT HERE! Better yet, join our jobs listing forum. SUBSCRIBE: icu-jobs-forum-subscribe@xxxxxxxxxx POST: icu-jobs-forum@xxxxxxxxxx -----------------------------------------------------------
BEGIN:VCARD VERSION:2.1 N:Stanislao;Tony FN:Tony Stanislao ORG:Pannaway Technologies TITLE:Senior PCB Design Engineer NOTE;ENCODING=QUOTED-PRINTABLE:Pannaway Technologies designs and develops converged broadband voice, video = and data platforms. Its solutions enable telecommunications providers world= wide to offer unified services to homes and businesses with an unbeatable va= lue proposition-opening new markets and creating new revenue streams.=0D=0A= =0D=0APannaway's pioneering Service Convergence Network (SCN=99) architectur= e offers telecommunications service providers the first carrier-class, end-t= o-end IP converged solution available anywhere, in turn allowing them to del= iver a secure combination of guaranteed billable services over a single conn= ection.=0D=0A=0D=0ARigorously architected and thoroughly tested by Pannaway'= s Ethernet IP and voice experts, the Service Convergence Network is the #1 s= ingle-vendor solution for secure, converged broadband transport services.= =0D=0A TEL;WORK;VOICE:603-766-5129 TEL;WORK;FAX:603-766-5150 ADR;WORK;ENCODING=QUOTED-PRINTABLE:;;215 Commerce Way =0D=0ASuite 3;Portsmouth;NH;03801;United States LABEL;WORK;ENCODING=QUOTED-PRINTABLE:215 Commerce Way =0D=0ASuite 3=0D=0APortsmouth, NH 03801=0D=0AUnited States URL;WORK:http://www.pannaway.com EMAIL;PREF;INTERNET:stanislao_t@xxxxxxxxxxxx REV:20031211T230145Z END:VCARD