Hi Joe,
How far through the boot process does it go when I/A is enabled? I'm guessing
it's the BSOD!
Early NT days we had issues with the differences between running unicore and
multicore kernels, sometimes it was an option in the bios to turn off multicore
on newer hardware and making sure unicore kernel was selected during the NT
install. I don't think there was an option on the original Foxboro GX240,
however GX240s that were purchased locally could have different motherboards
and bios chips, worth checking.
It's also possible the bindings on the network card need "fixing", I'm pretty
sure at v6.4 you still have the option to re-run the network install from the
setup CD, it's in Other Functions and Bindings. (distant memory sorry). You can
try it on the backup drive, rather than the production drive ;-)
Christian.
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Joseph M. Riccardi
Sent: Tuesday, 13 September 2016 11:58 AM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] P93 WinNT AW70 V6.4 with an external Winchester RAID 1
drive
I do not understand it but after some testing/swapping with different
equipment, I replaced the SCSI cable and can now boot into the Windows world...
Side note: How the Hell can the SCSISelect Utility see, check and verify the
external hard drive with a bad cable, but will not boot up?
Next issue... I can now boot into the Windows world with 3 different hard
drives from previous backups and RAID1 drives from the Production P93, but when
I check the "Start I/A at Boot" and reboot, the system crashes and goes into an
continuous reboot/crash cycle. It does that on all of the 3 different drives...
Is there any hope? What is causing the continuous reboot/crash cycle for the
"Start I/A at Boot" selection only?
Thanks
Joseph M. Riccardi
386-451-7607 Cell
Joe@xxxxxxxxxxxxx
"To give real service you must add something that cannot be bought or measured
with money; and that is sincerity and integrity." - Donald A. Adams
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Joseph M. Riccardi
Sent: Saturday, September 10, 2016 9:10 AM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] P93 WinNT AW70 V6.4 with an external Winchester RAID
1 drive
Scott,
But I cannot get to the BIOS settings? The F2 and F12 keys do not work.
They did work initially on one of them but neither do now. Just thinking that
maybe the keyboard is bad, but the arrow keys always worked. I will replace
the keyboard on Monday...
We ordered these rebuilt from a vendor by P-code which does not include the
internal hard drive. I did not even look for one but if the problem continues
I will open them up and check for one...
Thanks for the BIOS Parameter Settings reference but from what I always
remember about these is that both Primary Drive 0 & 1 were always set for OFF;
we have SCSI so as shown, OFF for SCSI). If I can get back in the BIOS
Parameter Settings I will double check the other settings Monday...
Thanks again, you have given me a reason to show up for work on Monday. :-)
Joseph M. Riccardi
386-451-7607 Cell
Joe@xxxxxxxxxxxxx
"To give real service you must add something that cannot be bought or measured
with money; and that is sincerity and integrity." - Donald A. Adams
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Landry, Scott
Sent: Saturday, September 10, 2016 11:47 AM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] P93 WinNT AW70 V6.4 with an external Winchester RAID
1 drive
Did you remove the internal hard drive
________________________________________
From: foxboro-bounce@xxxxxxxxxxxxx [foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of
Landry, Scott [Scott.Landry@xxxxxxxxxxxxxxxxxxxxxx]
Sent: Saturday, September 10, 2016 10:36 AM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] P93 WinNT AW70 V6.4 with an external Winchester RAID
1 drive
B0400RU - Rev A
Table 1-5. BIOS Parameter Settings
Primary Drive 0 Auto (for IDE, OFF for SCSI)
Primary Drive 1 OFF
Secondary Drive 0 (Auto) CD-ROM Reader
Secondary Drive 1 Auto if IDE Tape Drive is installed*)
Hard Drive Sequence
Note: For SCSI Only
<ENTER>
1. 01, 29160 A:00 Fujitsu Man 31844
2. Hard disk drive (not installed)
Boot Sequence <ENTER>
1. Diskette Drive
2. Hard disk drive C:
3. IDE CD-ROM device
________________________________________
From: foxboro-bounce@xxxxxxxxxxxxx [foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of
Joseph M. Riccardi [Joe@xxxxxxxxxxxxx]
Sent: Friday, September 09, 2016 8:33 PM
To: foxboro@xxxxxxxxxxxxx
Subject: [foxboro] P93 WinNT AW70 V6.4 with an external Winchester RAID 1 drive
Folks,
I am trying to replace a P93 Dell box that has an external Winchester RAID 1
drive with another identical P93 Dell box.
- The boot process stalls at. Slot 01, Ch A, ID 0, LUN 0 (no size is listed).
It does not even get to the Winchester RAID 1 drive; from memory that is the
next line in the boot process. I have tried numerous times using each of the
RAID 1 drives individually, and with both installed.
- Initially I could boot into the Setup and Boot Menu configurations using the
F2 and F12 keys but after about a dozen attempts neither of them work anymore.
- Also initially I could trigger the SCSISelect Utility using the <Ctrl><A>
keys but again that does not work anymore.
- When the SCSISelect Utility did work, I ran the Verify Test and it was
obvious the SCSI card could see the RAID drive(s) 17Gb.
- The Winchester RAID 1 drive passes diagnostics and indicates Ready.
- Based on a successful SCSISelect Utility test and a Winchester Ready status
I am guessing the SCSI interface is working properly but..
- Having no luck with the 1st P93 Dell box, I swapped it out with a 2nd P93
Dell box so it was now connected to the same Winchester RAID 1 drive.
- Unfortunately the 2nd one also stalls at. Slot 01, Ch A, ID 0, LUN 0.
Since Winchester RAID 1 drive and the SCSISelect Utility pass all tests, it
points back to the P93 Dell boxes as the culprit; but both with the same
problem? I am confused.
Any ideas/suggestions on why these P93 Dell boxes are stalling during the boot
process at. Slot 01, Ch A, ID 0, LUN 0 (no size is listed)?
Thanks
Joseph M. Riccardi
386-451-7607 Cell
Joe@xxxxxxxxxxxxx <mailto:Joe@xxxxxxxxxxxxx>
"To give real service you must add something that cannot be bought or measured
with money; and that is sincerity and integrity." - Donald A. Adams
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
______________________________________________________________________
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person.
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
______________________________________________________________________
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person.
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
______________________________________________________________________
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person.
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
