B0400RU – Rev A
Table 1-5. BIOS Parameter Settings
Primary Drive 0 Auto (for IDE, OFF for SCSI)
Primary Drive 1 OFF
Secondary Drive 0 (Auto) CD-ROM Reader
Secondary Drive 1 Auto if IDE Tape Drive is installed*)
Hard Drive Sequence
Note: For SCSI Only
<ENTER>
1. 01, 29160 A:00 Fujitsu Man 31844
2. Hard disk drive (not installed)
Boot Sequence <ENTER>
1. Diskette Drive
2. Hard disk drive C:
3. IDE CD-ROM device
________________________________________
From: foxboro-bounce@xxxxxxxxxxxxx [foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of
Joseph M. Riccardi [Joe@xxxxxxxxxxxxx]
Sent: Friday, September 09, 2016 8:33 PM
To: foxboro@xxxxxxxxxxxxx
Subject: [foxboro] P93 WinNT AW70 V6.4 with an external Winchester RAID 1 drive
Folks,
I am trying to replace a P93 Dell box that has an external Winchester RAID 1
drive with another identical P93 Dell box.
- The boot process stalls at. Slot 01, Ch A, ID 0, LUN 0 (no size is
listed). It does not even get to the Winchester RAID 1 drive; from memory
that is the next line in the boot process. I have tried numerous times
using each of the RAID 1 drives individually, and with both installed.
- Initially I could boot into the Setup and Boot Menu configurations using
the F2 and F12 keys but after about a dozen attempts neither of them work
anymore.
- Also initially I could trigger the SCSISelect Utility using the <Ctrl><A>
keys but again that does not work anymore.
- When the SCSISelect Utility did work, I ran the Verify Test and it was
obvious the SCSI card could see the RAID drive(s) 17Gb.
- The Winchester RAID 1 drive passes diagnostics and indicates Ready.
- Based on a successful SCSISelect Utility test and a Winchester Ready
status I am guessing the SCSI interface is working properly but..
- Having no luck with the 1st P93 Dell box, I swapped it out with a 2nd P93
Dell box so it was now connected to the same Winchester RAID 1 drive.
- Unfortunately the 2nd one also stalls at. Slot 01, Ch A, ID 0, LUN 0.
Since Winchester RAID 1 drive and the SCSISelect Utility pass all tests, it
points back to the P93 Dell boxes as the culprit; but both with the same
problem? I am confused.
Any ideas/suggestions on why these P93 Dell boxes are stalling during the
boot process at. Slot 01, Ch A, ID 0, LUN 0 (no size is listed)?
Thanks
Joseph M. Riccardi
386-451-7607 Cell
Joe@xxxxxxxxxxxxx <mailto:Joe@xxxxxxxxxxxxx>
"To give real service you must add something that cannot be bought or
measured with money; and that is sincerity and integrity." - Donald A. Adams
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
______________________________________________________________________
This email has been scanned by the Symantec Email Security.cloud service.
______________________________________________________________________
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person.
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
