[access-uk] Re: Advice for Using the Command Prompt
- From: "Darran Ross" <darran.ross@xxxxxxxxxxxxx>
- To: <access-uk@xxxxxxxxxxxxx>
- Date: Sat, 15 Jul 2006 15:29:47 +0100
Hi George.
Below is the resolution recommended for my set-up, namely Office 2003 with
Windows XP.
All the relevant info should be there.
Any advice, as ever, gratefully received.
Darran
Microsoft Update
Office 2003 Update fails to install with error 0x80070643
Last updated : 10/21/2005
Print |
Close
Problem description
You receive error 0x80070643 when you are installing Office 2003 Updates.
Updates fail to install because ose service is disabled or cannot be
started.
Applicable Office versions: Office 2003
Applicable operating systems and products
Windows 2000
Windows XP
Windows Server 2003
Resolutions
1. Start the ose service
Windows 2003/XP
Run the following command from command prompt to check the state of ose
service
sc qc ose
If the service is disabled, then run the command
sc config ose start= demand
Windows 2000
Click Start-Run
Type Services.msc and in the Open box and click OK.
Double click on the Office Source Engine service.
Set the Startup type to Manual and click OK.
For more information on this issue and alternate resolution please click on
the Microsoft Knowledge Base link below.
Did this resolve your problem?
Yes
No
For more information about Office 2003 Update fails to install with error
0x80070643, see article 903774 in the
Microsoft Knowledge Base.
Your answer is anonymous and is used to help improve content on this site.
----- Original Message -----
From: "George Bell" <george@xxxxxxxxxxxxxxxxxxx>
To: <access-uk@xxxxxxxxxxxxx>
Sent: Saturday, July 15, 2006 1:56 PM
Subject: [access-uk] Re: Advice for Using the Command Prompt
| Hi Darran,
|
| Not sure of your screen reader will function in this, but to
| get to a command line prompt, go to Start, Run, and in the
| dialog that comes up, type cmd and press Enter.
|
| You are now in what visually appears to be a DOS screen.
|
| Normally commands are entered as specified in MS's KB
| articles, and you then simply press Enter to execute the
| command.
|
| To get out of this command mode, type exit and press enter.
|
| If you can let me know the MS KB article number, I can try
| to be more specific as to what you need to do.
|
| George.
|
| -----Original Message-----
| From: access-uk@xxxxxxxxxxxxx
| [mailto:access-uk@xxxxxxxxxxxxx] On Behalf Of Darran Ross
| Sent: 14 July 2006 22:30
| To: Access-UK
| Subject: [access-uk] Advice for Using the Command Prompt
|
| Hi List.
|
| I've had a problem with updates for Office 2003 not being
| installed, and the MS Knowledge Base has suggested a
| resolution, but to do this I need to enter the Command
| Prompt. I've never been in there before, and there doesn't
| seem to be an edit field to enter the information required.
|
| Would someone with a little more experience of the Command
| Prompt mind letting me know how I should proceed in this
| area? How do I enter the command lines etc?
|
| Many thanks.
|
| Darran
|
| ** To leave the list, click on the immediately-following
| link:-
| **
| [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
| ** If this link doesn't work then send a message to:
| ** access-uk-request@xxxxxxxxxxxxx
| ** and in the Subject line type
| ** unsubscribe
| ** For other list commands such as vacation mode, click on
| the
| ** immediately-following link:-
| ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
| ** or send a message, to
| ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
|
| ** To leave the list, click on the immediately-following link:-
| ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
| ** If this link doesn't work then send a message to:
| ** access-uk-request@xxxxxxxxxxxxx
| ** and in the Subject line type
| ** unsubscribe
| ** For other list commands such as vacation mode, click on the
| ** immediately-following link:-
| ** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
| ** or send a message, to
| ** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
|
|
** To leave the list, click on the immediately-following link:-
** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=unsubscribe]
** If this link doesn't work then send a message to:
** access-uk-request@xxxxxxxxxxxxx
** and in the Subject line type
** unsubscribe
** For other list commands such as vacation mode, click on the
** immediately-following link:-
** [mailto:access-uk-request@xxxxxxxxxxxxx?subject=faq]
** or send a message, to
** access-uk-request@xxxxxxxxxxxxx with the Subject:- faq
Other related posts:
