[TechAssist] Re: Sony VCR SLV-360, cassette goes in and come right back out
- From: Gary McCartney <gary@xxxxxxxxxxx>
- To: techassist@xxxxxxxxxxxxx
- Date: Wed, 04 Dec 2002 00:02:32 -0500
Jeff, thanks. I put the original gear back in and the unit works. The
new gear is slightly different. Thanks To Panday for telling me the part
number for a kit to take care of this problem. It is Sony part #
A-7040-474-C. The photo in my catalog shows the kit consists of 4 gears
and a slide plate.
Gary McCartney
McCartney Electronics
7134 Fife Rd, RR 7
Guelph Ontario Canada N1H 6J4
Fax: (519)821-1530
email: gary (at) number63.ca
Jeff Dougherty wrote:
>
> Gary,
> Check positioning of the levers for the brakes.
> Jeff@xxxxxxxxxxxxxxxxxx
> FAX 717-564-4952
> Jeff Dougherty
> Intrepid Video & Electronics Be careful of your thoughts.
> 501 Luther Rd They may become your words
> Harrisburg, PA 17111 any moment.
> 717-909-8844
> VCR tips, electronics info & general interest.
> www.intrepid-video.com www.tech-repair.net
> www.thetoolcaddy.com www.9-11-2001tragedy.com
> ***********************************************************************
>
> ----- Original Message -----
> From: "Gary McCartney" <gary@xxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Tuesday, December 03, 2002 3:29 PM
> Subject: [TechAssist] Re: Sony VCR SLV-360, cassette goes in and come right
> back
> out
>
> Ed, thanks. I should have added a note in my message that I also slid
> the slide plate by hand and the guide posts loaded up all the way
> without any kind of binding. It really seems as the large black loading
> gear is not able to rotate far enough to engage the slide plate teeth.
> The black gear can't turn as far as I think it should because the
> flanges on the FL loading gear I replaced hit up against it and prevent
> further rotation. I have to be doing something wrong but what?
>
> Gary McCartney
>
> McCartney Electronics
> 7134 Fife Rd, RR 7
> Guelph Ontario Canada N1H 6J4
> Fax: (519)821-1530
> email: gary (at) number63.ca
>
> Edward Gaidies wrote:
> >
> > Sounds like linkage to the t/u and supply guides is out of allignment. Not
> > sure though, since I would never get approval from customer for this type of
> > repair....Sony...or not. Also I thought... either you or I.. had one of
> > these gears worn in another Sony, and found out later that this gear was not
> > really the problem, but something else.
> >
> > -Ed-
> >
> > -Ed-
> > ----- Original Message -----
> > From: "Gary McCartney" <gary@xxxxxxxxxxx>
> > To: <techassist@xxxxxxxxxxxxx>
> > Sent: Tuesday, December 03, 2002 3:01 PM
> > Subject: [TechAssist] Sony VCR SLV-360, cassette goes in and come right back
> > out
> >
> > >
> > > This Sony VCR model SLV360 came into the shop with a cassette stuck
> > > inside it. I had to remove the carriage in order to free the cassette. I
> > > noticed that the FL-loading gear # 3-958-156-03 had some chewed teeth so
> > > I ordered a new one. Now I have it all installed back together and the
> > > cassette will go into the machine, all the way down to it's resting
> > > position but instead of the mechanism pulling the tape out of the
> > > cassette and loading it, the cassette just reverses and ejects on me. I
> > > have cleaned the mode switch. Also checked the alignment of the loading
> > > gears, which look ok to me although I don't have a manual to do this by.
> > > for a photo of my alignment, clink on link:
> > >
> > >
> > > http://www.number63.ca/gears.jpg
> > >
> > >
> > > I cleaned the grease off the slide plate "rack" gear teeth and they look
> > > as I believe they should. The first tooth is only half as high as the
> > > rest but it looks like it was manufacturerd that way, not as if it looks
> > > broken.
> > >
> > >
> > > To see picture of teeth on slide plate, click on link:
> > >
> > > http://www.number63.ca/deck.jpg
> > >
> > >
> > > I removed the loading motor so I could spin the gears manually and after
> > > the cassette loading is complete, the gears lock up and won't allow the
> > > tape loading procedure to start. It appears as though it's the fault of
> > > the FL loading gear which I replaced because as the large black gear
> > > rotates, the FL gear's flanges hit the teeth on the black gear and
> > > prevent any further rotation. Still, I'm sure the FL gear is in proper
> > > position.
> > >
> > >
> > > I'm stuck on this one, any help appreciated.
> > > --
> > >
> > >
> > >
> > >
> > > Gary McCartney
> > >
> > > McCartney Electronics
> > > 7134 Fife Rd, RR 7
> > > Guelph Ontario Canada N1H 6J4
> > > Fax: (519)821-1530
> > > email: gary (at) number63.ca
> > >
> > > ------------------------------------------
> > > To REMOVE your email address, click here:
> > > http://www.tech-assist.org/unsubb.html
> > > To CHANGE your email address, click here:
> > > http://www.techassist.net/forms/change.html
> > > ------------------------------------------
> > > ***NEW*** Tips Added Instantly!!!***
> > > Submit Repair Tips here:
> > > http://www.tech-assist.org/secure/tip/
> >
> > ------------------------------------------
> > To REMOVE your email address, click here:
> > http://www.tech-assist.org/unsubb.html
> > To CHANGE your email address, click here:
> > http://www.techassist.net/forms/change.html
> > ------------------------------------------
> > ***NEW*** Tips Added Instantly!!!***
> > Submit Repair Tips here:
> > http://www.tech-assist.org/secure/tip/
>
> --
>
> Gary McCartney
>
> McCartney Electronics
> 7134 Fife Rd, RR 7
> Guelph Ontario Canada N1H 6J4
> Fax: (519)821-1530
> email: gary (at) number63.ca
>
> ------------------------------------------
> To REMOVE your email address, click here:
> http://www.tech-assist.org/unsubb.html
> To CHANGE your email address, click here:
> http://www.techassist.net/forms/change.html
> ------------------------------------------
> ***NEW*** Tips Added Instantly!!!***
> Submit Repair Tips here:
> http://www.tech-assist.org/secure/tip/
>
> ------------------------------------------
> To REMOVE your email address, click here:
> http://www.tech-assist.org/unsubb.html
> To CHANGE your email address, click here:
> http://www.techassist.net/forms/change.html
> ------------------------------------------
> ***NEW*** Tips Added Instantly!!!***
> Submit Repair Tips here:
> http://www.tech-assist.org/secure/tip/
--
------------------------------------------
To REMOVE your email address, click here:
http://www.tech-assist.org/unsubb.html
To CHANGE your email address, click here:
http://www.techassist.net/forms/change.html
------------------------------------------
***NEW*** Tips Added Instantly!!!***
Submit Repair Tips here:
http://www.tech-assist.org/secure/tip/
Other related posts:
