[TechAssist] Re: Samsung 17" Monitor SyncMaster 750s

Hello Ed,
Yes, I sure don't see as many as I used to. I sometimes find one from a junker, 
and hard wire if unit is worth the effort. just finding a compatible strain 
relief is the hard part. I'll have to find out where we used to get monitor 
cables from, but maybe Samsung would have it.



 Thanx,

Scott Beebe
Ohm Electronics Inc.
609 W. Clinton St.
Ithaca NY 14850
Voice: (607) 273-8406
Fax: (607) 273-8743
WWW.OhmElectronicsInc.com
mailto:Scott@xxxxxxxxxxxxxxxxxxxxx

Thursday, April 8, 2004, 11:03:34 AM, you wrote:

Ed> I would too Scott, if I knew where you get parts for Monitors. I don't do
Ed> many.

Ed> -Ed-



Ed> Tel-Tek Electronics
Ed> Ontario-Canada

Ed> teltek3@xxxxxxxxxxxx
Ed> ----- Original Message ----- 
Ed> From: "Scott Beebe" <Scott@xxxxxxxxxxxxxxxxxxxxx>
Ed> To: "majorthom@xxxxxxxxxxxxx" <techassist@xxxxxxxxxxxxx>
Ed> Sent: Thursday, April 08, 2004 10:23 AM
Ed> Subject: [TechAssist] Re: Samsung 17" Monitor SyncMaster 750s


>> Hello Ed,
>>
>> I agree with peter. I will replace the whole cable, as I would not want to
Ed> go to the trouble of replacing the end and find I still have an intermattant
Ed> in the cable. Also, on another note, Peter, I think your sig file is going
Ed> at the very bottem. When you reply, you should see what your sending in the
Ed> editor before being sent. (Your sig file)
>>
>>
>>  Thanx,
>>
>> Scott Beebe
>> Ohm Electronics Inc.
>> 609 W. Clinton St.
>> Ithaca NY 14850
>> Voice: (607) 273-8406
>> Fax: (607) 273-8743
>> WWW.OhmElectronicsInc.com
>> mailto:Scott@xxxxxxxxxxxxxxxxxxxxx
>>
>> Thursday, April 8, 2004, 10:00:10 AM, you wrote:
>>
>> > Hi Ed -This is a real pain.I do a lot of
>> > monitors and since the DB15 plug is molded,the cord must be
>> > replaced.I'll look in my junk if you can show or tell me
>> > what's on the monitor end of the cable...........Regards,
>> > Pete
>>
>> > Ed Gaidies <teltek3@xxxxxxxxxxxx> wrote:
>> > Need some advice guys.
>> > Customer brought in a Samsung Monitor that was
>> > not getting any input from
>> > the Video Card. I see a Pin is missing from the
>> > plug. (broken off). What's
>> > the easiest and cheapest way to repair these
>> > molded plugs. Or is it better
>> > to try to get a new Wiring Harness, if
>> > available. There are just 2 sets of
>> > plugs coming out at the Monitor End.
>>
>> > Thanks.
>>
>>
>> > -Ed-
>>
>>
>>
>> > Tel-Tek Electronics
>> > Ontario-Canada
>>
>> > teltek3@xxxxxxxxxxxx
>>
>>
>>
>> --------------------------------------------------------------------------
Ed> ---
>> > Lost Password:
>> > http://www.tech-assist.org and select "Login Problems?".
>> > Email Archives:
>> > http://www.freelists.org/archives/techassist/
>>
>> > Peter Neal
>> > Neal Electronics
>> > 1905 E. Wm.Cannon
>> > Austin,TX  78756
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> --------------------------------------------------------------------------
Ed> ---
>> > Lost Password:
>> > http://www.tech-assist.org  and select "Login Problems?".
>> > Email Archives:
>> > http://www.freelists.org/archives/techassist/
>>
>>
>> --------------------------------------------------------------------------
Ed> ---
>> Lost Password:
>> http://www.tech-assist.org  and select "Login Problems?".
>> Email Archives:
>> http://www.freelists.org/archives/techassist/


Ed> 
-----------------------------------------------------------------------------
Ed> Lost Password:
Ed> http://www.tech-assist.org  and select "Login Problems?".
Ed> Email Archives:
Ed> http://www.freelists.org/archives/techassist/


-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org  and select "Login Problems?".
Email Archives:
http://www.freelists.org/archives/techassist/

Other related posts: