Thanks CR4403 and C4407 certainly fixed the bow. thanks Al ,and Dennis. And Everyone for the help. Richard ----- Original Message ----- From: "al m" <ampm@xxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Tuesday, January 08, 2002 7:06 AM Subject: [TechAssist] Re: CTC 187BD2 FIXED has bow now. > > dennis change cr4403 and c4407 the cap is probably bulged.had the same > problem this fixed it. > al marquardt > ampm@xxxxxxx > ----- Original Message ----- > From: "Dennis Viereck" <wa6ati@xxxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Tuesday, January 08, 2002 12:34 AM > Subject: [TechAssist] Re: CTC 187BD2 FIXED has bow now. > > > > I would suspect components in the Pin cushion circuit rather than C4303 in > the > > horizontal driver circuit. CR4403 should be a suspect or the components in > the > > Pin output circuit. I'm not sure what your chassis is using for a Pin > cushion > > modulator, but I think it is on a small vertically mounted CBA. > > > > It is possible that you could have 1 of two different boards. Q4851 is the > Pin > > cushion output transistor. It is an NPN used on one of the two modules. > > > > The other module uses an PNP for the Pincushion output. It is location > Q4802. > > > > If either one of these transistors or associated circuits fail to operate > the > > width and E/W pincushion will be effected. > > > > Dennnis Viereck > > > > > > "Richard Golden d.b.a. Golden Video Repair Center" wrote: > > > > > CTC187bd2 Came in dead. > > > > > > Thanks Dennis,Gonzalo,Al,Wayne for your help; > > > > > > I replaced U4101 and CR4109, unit is working now.But > > > had slight bow on sides.I replaced CR4303 took some > > > of the bow out.It now has a full picture,but still bowed. > > > And it is now, a little to wide.And picture narrows when I change > channels, > > > or G2 (screen) I suspect C4303.I don,t > > > have it in stock,I am going to order it tomorrow, > > > thanks very much. > > > Richard > > > > > > ----- Original Message ----- > > > From: "Dennis Viereck" <wa6ati@xxxxxxxxxxxxxx> > > > To: <techassist@xxxxxxxxxxxxx> > > > Sent: Sunday, January 06, 2002 10:20 PM > > > Subject: [TechAssist] Re: CTC 187BD2 dead > > > > > > > I'm confused. Originally you stated that U4101(4) =0 volts. Are you > now > > > saying > > > > that it is really 1.3 volts? Or only when you isolate the pin on > U4101(4)? > > > > > > > > It appear that U4101 is not running. I would try to start this device > at > > > low > > > > voltage. Using a variac at 10 vac should start this supply running and > > > when the > > > > the A.C. voltage gets to about 40 vac the secondary will rise to near > > > normal > > > > levels. If it never starts oscillation then I would suspect U4101. > > > > > > > > If oscillation starts and exceeds secondary voltages and shuts off > suspect > > > > C4127 or associated circuit. This is the filter for the feedback > > > comparison for > > > > the error amp in U4101. > > > > > > > > Dennis Viereck > > > > > > > > > > > > > > > > > > > > "Richard Golden d.b.a. Golden Video Repair Center" wrote: > > > > > > > > > r4104 has 165v in out 1.3v out , then unsoldered u4101 now has 144v > out > > > of > > > > > r4104, resistor is good, replace u4101 or? > > > > > thanks > > > > > Richard > > > > > > > > > > ----- Original Message ----- > > > > > From: "Dennis Viereck" <wa6ati@xxxxxxxxxxxxxx> > > > > > To: <techassist@xxxxxxxxxxxxx> > > > > > Sent: Sunday, January 06, 2002 9:03 PM > > > > > Subject: [TechAssist] Re: CTC 187BD2 dead > > > > > > > > > > > > > > > > > Assuming U4101(4) is at 0 volts then I would have to check R4104 a > 1.5 > > > > > > meg 1/2 watt resistor. This is the soft start resistor. It may be > open > > > > > > or something is loading down the input of U4104(4) > > > > > > > > > > > > Dennis Viereck > > > > > > > > > > > > Richard Golden wrote: > > > > > > > > > > > > > CTC187BD2 d.o.a checked common known problems > > > > > > > with this chassic everything checks good ohms check > > > > > > > etc. replaced cr4106 cr4107,fuse good ,hot qood > > > > > > > Q4101( C) +5.99v,Q4301=(C)=0v, U3201 0v on all, > > > > > > > r4104 =+165v Q4303=0v, ( regulator #1=+1.5v, > > > > > > > 2&3=0v), (r4128= -2v ), U4101 pins (1=-2v), > > > > > > > (2=-1.2v), (3=0),( > > > > > > > 4=0),(5=+1.5v),(6=+1.5v),7=+.019v), > > > > > > > (8=0v), (9=0v), (10=0v), (11&12 =+163v) > > > > > > > any help appreciated > > > > > > > > Richard > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > ===== > > > > > > > > Richard Golden > > > > > > > > Golden Video Repair Center > > > > > > > > 1214 e. 6th street > > > > > > > > ontario ca. 91764 > > > > > > > > (909)988-3356 > > > > > > > > > > > > > > > > reldong@xxxxxxxxx > > > > > > > > > > > > > > > > __________________________________________________ > > > > > > > > > > > > > > ===== > > > > > > > Richard Golden > > > > > > > Golden Video Repair Center > > > > > > > 1214 e. 6th street > > > > > > > ontario ca. 91764 > > > > > > > (909)988-3356 > > > > > > > > > > > > > > reldong@xxxxxxxxx > > > > > > > > > > > > > > __________________________________________________ > > > > > > > Do You Yahoo!? > > > > > > > Send FREE video emails in Yahoo! Mail! > > > > > > > http://promo.yahoo.com/videomail/ > > > > > > > ------------------------------------------ > > > > > > > Help make your TechAssist database better! > > > > > > > Submit your fixes here: > http://circuitwork.com/techassist/tip/#tips > > > > > > > ------------------------------------------ > > > > > > > To UNSUBSCRIBE your email address, click here: > > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > > Or send a BLANK email with unsubscribe in the > > > > > > > SUBJECT field to the address above. > > > > > > > > > > > > ------------------------------------------ > > > > > > Help make your TechAssist database better! > > > > > > Submit your fixes here: > http://circuitwork.com/techassist/tip/#tips > > > > > > ------------------------------------------ > > > > > > To UNSUBSCRIBE your email address, click here: > > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > > Or send a BLANK email with unsubscribe in the > > > > > > SUBJECT field to the address above. > > > > > > > > > > ---------------------------------------------------- > > > > > Sign Up for NetZero Platinum Today > > > > > Only $9.95 per month! > > > > > http://my.netzero.net/s/signup?r=platinum&refcd=PT97 > > > > > ------------------------------------------ > > > > > Help make your TechAssist database better! > > > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > > > ------------------------------------------ > > > > > To UNSUBSCRIBE your email address, click here: > > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > > Or send a BLANK email with unsubscribe in the > > > > > SUBJECT field to the address above. > > > > > > > > > > > > ------------------------------------------ > > > > Help make your TechAssist database better! > > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > > ------------------------------------------ > > > > To UNSUBSCRIBE your email address, click here: > > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > > Or send a BLANK email with unsubscribe in the > > > > SUBJECT field to the address above. > > > > > > ---------------------------------------------------- > > > Sign Up for NetZero Platinum Today > > > Only $9.95 per month! > > > http://my.netzero.net/s/signup?r=platinum&refcd=PT97 > > > ------------------------------------------ > > > Help make your TechAssist database better! > > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > > ------------------------------------------ > > > To UNSUBSCRIBE your email address, click here: > > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > > Or send a BLANK email with unsubscribe in the > > > SUBJECT field to the address above. > > > > > > ------------------------------------------ > > Help make your TechAssist database better! > > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > > ------------------------------------------ > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > Or send a BLANK email with unsubscribe in the > > SUBJECT field to the address above. > > > > > > > > > ------------------------------------------ > Help make your TechAssist database better! > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > ------------------------------------------ > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > Or send a BLANK email with unsubscribe in the > SUBJECT field to the address above. ---------------------------------------------------- Sign Up for NetZero Platinum Today Only $9.95 per month! http://my.netzero.net/s/signup?r=platinum&refcd=PT97 ------------------------------------------ Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.