Hae finally it worked, don't know why it refused to work, but i followed bar numbering etc and it worked, but the problem is now if the 1st or 2nd ending will start in teh middle of a bar and end in teh middle of another bar, i know this, but sibelius refuse to count bar numbers after this. any ideas? On 12/7/14, saeed Mirzazadeh <saeedm19@xxxxxxxxx> wrote: > Dave, > I didn't mean and I don't think if Ramy meant putting first and second > ending inside a bar. But it's possible if you start repeating a > passage at the third beat of bar 5 for example, and end at the second > beat of bar 6. > Regards, > Saeed > > On 12/7/14, Dave Carlson <dgcarlson@xxxxxxxxxxxxx> wrote: >> Saeed, >> >> I suspect that you are correct about the selection. I have not worked on >> a >> score for a few years, so my memory is not so good as it once was. Good >> advice on splitting the bar, but again I wonder how a repeat can >> start/end >> inside a bar. I think that will cause the tempo to "break" at that point? >> >> Dave Carlson >> Oregonian, woodworker, and pioneer >> >> ----- Original Message ----- >> From: "saeed Mirzazadeh" <saeedm19@xxxxxxxxx> >> To: <sib-access@xxxxxxxxxxxxx> >> Sent: Sunday, December 07, 2014 06:59 AM >> Subject: [sib-access] Re: [Bulk] Re: [Bulk] 1st and 2nd endings >> >> >> Ramy, >> I didn't say so! No need of 2 end-repeat barlines. >> About repeating from the middle of bar, calassically if the >> repeatition begins from the third beat of a 4/4 bar, it has to be >> ended at the second beat of an other bar. The symmetry has to be >> followed. >> Dave, >> As far as my experience, there's no need to select the intervals >> between first and second ending line. >> Regards, >> Saeed >> >> On 12/7/14, Dave Carlson <dgcarlson@xxxxxxxxxxxxx> wrote: >>> Hello Ramy, >>> >>> First, I don't know how you can possibly start a repeat line inside the >>> middle of a bar -- you'll have to figure out a way to write the score >>> differently to not do this. Repeat sections as well as repeats need to >>> start >>> >>> and end on the exact bar lines. >>> >>> As for your overall problem, I wonder if you're not selecting all the >>> bars >>> 15 through 18 before you apply the first repeat line over them? >>> >>> Dave Carlson >>> Oregonian, woodworker, and pioneer >>> >>> ----- Original Message ----- >>> From: "Ramy Moustafa" <nagham.lovers@xxxxxxxxx> >>> To: <sib-access@xxxxxxxxxxxxx> >>> Sent: Saturday, December 06, 2014 11:32 PM >>> Subject: [Bulk] [sib-access] Re: [Bulk] 1st and 2nd endings >>> >>> >>> Hi sir Dave: >>> Thanks so much for your reply. >>> i followed all your words, and i read what you wrote in sibelius tips >>> and tricks, but, to be sure, >>> i will describe here what i want to do: >>> i need to play from bar 10 to bar15, then i have a passage from bar 16 >>> to bar18, then teh player will play from bar 10 to bar 15, then he >>> will play from bar 19 to bar 23, and continue the score >>> i did the following: >>> i put a start repat line on bar 10, i put 1st ending, on bar 16 to bar >>> 18, i put an end repeat line at teh end of bar 18, and i put 2nd >>> ending "not the closed one" on bar 19 to 23, >>> this is what i did exactly, but as i stated, sibelius play this >>> incorrectly. >>> and by th e way, if the 1st or 2nd enging start at the middile of the >>> bar, how can i do that? i tried doing this in previous score, but the >>> line layed on the hole bar. >>> help please?? >>> >>> On 12/7/14, Dave Carlson <dgcarlson@xxxxxxxxxxxxx> wrote: >>>> Ramy, >>>> >>>> There are several "Line" types and also several different repeat line >>>> types. >>>> >>>> I think you may have selected those with no numbering, and should go >>>> back >>>> and check. Also I expect that you've already put the end repeat bar at >>>> the >>>> end of the first repeat section? >>>> >>>> Dave Carlson >>>> Oregonian, woodworker, and pioneer >>>> >>>> ----- Original Message ----- >>>> From: "ramy moustafa" <nagham.lovers@xxxxxxxxx> >>>> To: "sib access mailing list" <sib-access@xxxxxxxxxxxxx> >>>> Sent: Saturday, December 06, 2014 09:38 PM >>>> Subject: [Bulk] [sib-access] 1st and 2nd endings >>>> >>>> >>>> Hello all >>>> i'm trying to put 1st and 2nd endings on my score, i followed all dann >>>> discribed and i put the end repeat after the 1st ending and i put the >>>> 2nd >>>> ending-opened after this on the next bar. >>>> my 2 problems are that sibelius repeat them in a wrong way, don't know >>>> why? >>>> >>>> and, after the 2nd ending, sibelius loses the bar numbering at all, >>>> this >>>> is >>>> >>>> not a jaws issue, even sited person told me that, numbers disappeared, >>>> what am i doing wrong? >>>> thanks. >>>> >>>> Ramy moustafa saber >>>> Musicc instructor at: >>>> faculty of musical education >>>> music arranger and sound engineer >>>> Sent from my iPhoneIf you wish to unsubscribe, send a blank message >>>> with the single word, unsubscribe - in the Subject line to: >>>> sib-access-request@xxxxxxxxxxxxx >>>> >>>> If you wish to unsubscribe, send a blank message >>>> with the single word, unsubscribe - in the Subject line to: >>>> sib-access-request@xxxxxxxxxxxxx >>>> >>> If you wish to unsubscribe, send a blank message >>> with the single word, unsubscribe - in the Subject line to: >>> sib-access-request@xxxxxxxxxxxxx >>> >>> If you wish to unsubscribe, send a blank message >>> with the single word, unsubscribe - in the Subject line to: >>> sib-access-request@xxxxxxxxxxxxx >>> >> >> >> -- >> My Youtube Channel: >> https://www.youtube.com/user/s1n2m >> My SoundCloud: >> https://soundcloud.com/sanonosa >> If you wish to unsubscribe, send a blank message >> with the single word, unsubscribe - in the Subject line to: >> sib-access-request@xxxxxxxxxxxxx >> >> If you wish to unsubscribe, send a blank message >> with the single word, unsubscribe - in the Subject line to: >> sib-access-request@xxxxxxxxxxxxx >> > > > -- > My Youtube Channel: > https://www.youtube.com/user/s1n2m > My SoundCloud: > https://soundcloud.com/sanonosa > If you wish to unsubscribe, send a blank message > with the single word, unsubscribe - in the Subject line to: > sib-access-request@xxxxxxxxxxxxx > If you wish to unsubscribe, send a blank message with the single word, unsubscribe - in the Subject line to: sib-access-request@xxxxxxxxxxxxx