[PCB_FORUM] Re: Flash Symbol

Hi Everyone,
 Shirley was looking for an oblong FLASH (thermal) not an oblong pad....
Hence the comment about "if they can make an oblong pad why not an option
for an oblong flash".... Currently I know of no way other than the one I
responded with to making an oblong FLASH.
Thanks,
Dharma  


KAW/USA Ltd. 
39 Simon Street, #4 
Nashua, NH 03060 
603-886-8711 x212 
603-881-8763 fax 

Confidentiality Notice: This email and any accompanying documents contain
information that is confidential, privileged or exempt from disclosure under
applicable law and is intended for the exclusive use of the addressee. This
information is private and protected by law. If you are not the intended
recipient, or have received this email in error, you are hereby notified
that any disclosure, copying, distribution or use of the contents of this
document in any manner is strictly prohibited.


-----Original Message-----
From: Shahed.Safavi-Bayat@xxxxxxxxxxxxxxxxxxxxx
[mailto:Shahed.Safavi-Bayat@xxxxxxxxxxxxxxxxxxxxx] 
Sent: Wednesday, July 22, 2009 4:13 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Cc: icu-pcb-forum@xxxxxxxxxxxxx; icu-pcb-forum-bounce@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Flash Symbol

Oblong pad is available in 15.7 and up. Neither of previous emails mentioned
which version of Allegro is.

Shahed


|------------>
| From:      |
|------------>
 
>---------------------------------------------------------------------------
-----------------------------------------------------------------------|
  |davidkel <davidkel@xxxxxxxxx>
|
 
>---------------------------------------------------------------------------
-----------------------------------------------------------------------|
|------------>
| To:        |
|------------>
 
>---------------------------------------------------------------------------
-----------------------------------------------------------------------|
  |<icu-pcb-forum@xxxxxxxxxxxxx>
|
 
>---------------------------------------------------------------------------
-----------------------------------------------------------------------|
|------------>
| Date:      |
|------------>
 
>---------------------------------------------------------------------------
-----------------------------------------------------------------------|
  |07/22/2009 04:09 PM
|
 
>---------------------------------------------------------------------------
-----------------------------------------------------------------------|
|------------>
| Subject:   |
|------------>
 
>---------------------------------------------------------------------------
-----------------------------------------------------------------------|
  |[PCB_FORUM] Re: Flash Symbol
|
 
>---------------------------------------------------------------------------
-----------------------------------------------------------------------|





Hi

Maybe I missed something here. But you can make an oblong pad by specifying
the height And width and the tool makes the pad for you. Why do you need to
make the shape?

Dave


On 7/22/09 2:07 PM, "Dharma Kemp-Bresett" <dharma@xxxxxxx> wrote:

      Hi Shirley,
       I agree but unless I just don't know about it this is the only
      option we have for now.... Anybody willing/able to prove me wrong I
      would be VERY happy to hear it. As would Shirley, I am assuming...
      :-)
      Thanks,
      Dharma

      KAW/USA Ltd.
      39 Simon Street, #4
      Nashua, NH 03060
      603-886-8711 x212
      603-881-8763 fax

      Confidentiality Notice: This email and any accompanying documents
      contain information that is confidential, privileged or exempt from
      disclosure under applicable law and is intended for the exclusive use
      of the addressee. This information is private and protected by law.
      If you are not the intended recipient, or have received this email in
      error, you are hereby notified that any disclosure, copying,
      distribution or use of the contents of this document in any manner is
      strictly prohibited.



      From: Bradley, Shirley [mailto:shirley.bradley@xxxxxxxxxxxx]
      Sent: Wednesday, July 22, 2009 4:00 PM
      To: icu-pcb-forum@xxxxxxxxxxxxx
      Subject: [PCB_FORUM] Re: Flash Symbol

      This is similar to what I did. Made it for the smallest dimension,
      pulled it apart for the long dimension and stretched the sides. If
      Cadence made it easy to make a round flash and it is easy to make an
      oval pad, they should have an easy way to make the oval flash.

      Thanks for your answer.
      Shirley M. Bradley
      Intermec
      tel: 319.369.3328
      shirley.bradley@xxxxxxxxxxxx



      From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [
      mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Dharma
      Kemp-Bresett
      Sent: Wednesday, July 22, 2009 2:51 PM
      To: icu-pcb-forum@xxxxxxxxxxxxx
      Subject: [PCB_FORUM] Re: Flash Symbol

      Hi Shirley,
      Yes, Build a normal flash to the size of your smallest dimension then
      open it as a  symbol .dra and then separate the two "sides" and
      stretch (extend) the long sides by the difference between your
      shortest and longest dimensions. If this "quick and dirty" response
      is confusing to you ( and I admit it might be) reply to me offline
      and I can give you more detailed info.
      Thanks,
      Dharma

      KAW/USA Ltd.
      39 Simon Street, #4
      Nashua, NH 03060
      603-886-8711 x212
      603-881-8763 fax

      Confidentiality Notice: This email and any accompanying documents
      contain information that is confidential, privileged or exempt from
      disclosure under applicable law and is intended for the exclusive use
      of the addressee. This information is private and protected by law.
      If you are not the intended recipient, or have received this email in
      error, you are hereby notified that any disclosure, copying,
      distribution or use of the contents of this document in any manner is
      strictly prohibited.



      From: Bradley, Shirley [mailto:shirley.bradley@xxxxxxxxxxxx]
      Sent: Wednesday, July 22, 2009 3:43 PM
      To: icu-pcb-forum@xxxxxxxxxxxxx
      Subject: [PCB_FORUM] Flash Symbol

      Greetings,

      Is there an easy way to make a flash symbol for an oval plated hole?

      Thanks,

      Shirley M. Bradley
      Intermec
      tel: 319.369.3328
      shirley.bradley@xxxxxxxxxxxx
      This message is intended only for the named recipient. If you are not
      the intended recipient, you are notified that disclosing, copying,
      distributing or taking any action based on the contents of this
      information is strictly prohibited.

      This message is intended only for the named recipient. If you are not
      the intended recipient, you are notified that disclosing, copying,
      distributing or taking any action based on the contents of this
      information is strictly prohibited.



-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe

To view the archives of this list go to
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------


-----------------------------------------------------------
To subscribe/unsubscribe: 
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe

To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------

Other related posts: