Joe,
3. Configure the time server for the NTP software
The file d:\opt\foxind\NTPTimeSync\data\ntp.conf must be modified to contain the
IP address of the NTP server. This file has a default entry of “server
127.127.0.1”.
Only the IP address 127.127.0.1 should be edited.
Then copy the ntp.conf to the c:\winnt\system32\drivers\etc directory.
6. Reboot the AW.
Regards,
Scott
________________________________________
From: foxboro-bounce@xxxxxxxxxxxxx [foxboro-bounce@xxxxxxxxxxxxx] On Behalf Of
Joseph M. Riccardi [Joe@xxxxxxxxxxxxx]
Sent: Tuesday, November 10, 2015 3:24 PM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] WinNT V6.4 time change DST *****With AIMAT V3.2*****
Well, I have come full circle back to Scott's info... I have searched your
GCS site for the NTP TimeSync User Guide referenced and I get every User
Guide but this one. Where did you get the copy you quoted from below? At
this point all I really need is the location of the NTP TimeSync file that
contains the server name or the IP address it is looking to sync with. I
find out that corporate server IP address has changed.
Anyone have a copy of that User Guide or know the location of the info I
need?
Thanks
Joseph M. Riccardi
386-451-7607 Cell
Joe@xxxxxxxxxxxxx
"To give real service you must add something that cannot be bought or
measured with money; and that is sincerity and integrity." - Donald A. Adams
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On
Behalf Of Joseph M. Riccardi
Sent: Friday, November 6, 2015 6:00 PM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] WinNT V6.4 time change DST *****With AIMAT V3.2*****
Scott,
Thanks for all of the info again...
Joseph M. Riccardi
386-451-7607 Cell
Joe@xxxxxxxxxxxxx
"To give real service you must add something that cannot be bought or
measured with money; and that is sincerity and integrity." - Donald A. Adams
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On
Behalf Of Landry, Scott
Sent: Friday, November 6, 2015 11:18 AM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] WinNT V6.4 time change DST *****With AIMAT V3.2*****
Joe,
That paragraph I attached is straight out of ;
NTP TimeSync User Guide
(NT Rev 6.2.1) (Unix Rev 7.0.0)
NTP TimeSync SD 983-097B
Utilities Engineering , The Foxboro Co. January 2003
So I assume you are using that package, maybe an earlier or later version
FV/FD V9.0.4 is the latest/last version for NT
AIM V3.3 is the latest/last version for NT
The advisories Schneider/Foxboro sends out twice a year on DST for the
most part
center around Foxview , AIM and the CAD (and the other instances,
AHD,MRD, etc.) as applied to
the system you are referencing.
Below is from the same document referenced above, initial setup
5. Edit the file d:\opt\foxind\NTPTimeSync\data\TZOffset to contain the
seconds
offset from GMT time that you would like the I/A’s system time to be
set to. (i.e. for
Eastern Standard Time Zone with the time source’s time set to UTC,
place –14400 in
this file, which will set I/A’s system time 4 hours behind UTC time)
6. Reboot the AW.
I have never used this package so I am assuming that you have few choices
here:
1. Compensate for DST by adjusting TZOffset twice a year
2. Use an NTP Time Source with DST and manually adjust the SMDH time
twice a year
3. Talk to Sylvain Nadeau in the Montreal office to see if he will still
sell TCP TimeSync for NT
I would also contact your local Foxboro Sales Rep. , Foxboro Service Rep.
for consultation on a System Upgrade.
Regards,
Scott
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person.
_________________________________________________________________________
This mailing list is neither sponsored nor endorsed by Schneider Electric
(formerly The Foxboro Company). Use the info you obtain here at your own
risks. See the disclaimer at www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
