[THIN] Re: Ghosting HP DL 380s
- From: "Bruce Heavner" <bheavner@xxxxxxxxxxxx>
- To: <thin@xxxxxxxxxxxxx>
- Date: Fri, 20 Aug 2004 14:43:08 -0500
Just use the protocol.ini on your boot disk, in the [driver] section
(usually [q57] to set
LinkSpeed=100
Duplex=full
It should have an example protocol.ini that you can use.
Bruce Heavner
RapidApp
Sr. Network Engineer
bheavner@xxxxxxxxxxxx
-----Original Message-----
From: Landin, Mark [mailto:Mark.Landin@xxxxxxxxxxxxxxxx]
Sent: Friday, August 20, 2004 1:53 PM
To: thin@xxxxxxxxxxxxx
Subject: [THIN] Re: Ghosting HP DL 380s
This could be caused by a duplex mismatch between the switch and the
NIC. Make sure your switch is set to 100/Half (since it seems that will
be easier to go that setting your server NIC to 100/Full) and see what
happens.
And, again, why aren't you using the gigabit card? Do you not have a
gigabit switch?
> -----Original Message-----
> From: thin-bounce@xxxxxxxxxxxxx
> [mailto:thin-bounce@xxxxxxxxxxxxx] On Behalf Of Seitz, Linden
> Sent: Friday, August 20, 2004 1:22 PM
> To: 'thin@xxxxxxxxxxxxx'
> Subject: [THIN] Re: Ghosting HP DL 380s
>
> I see a big difference speed-wise between the two.... I
> hardcode 100 Full on other NIC drivers and get 200mb/minute
> sending; 100/Half gets me 20mb/minute sending. If anyone has
> the same problem and can help me out, thanks!
>
> -----Original Message-----
> From: thin-bounce@xxxxxxxxxxxxx [mailto:thin-bounce@xxxxxxxxxxxxx]On
> Behalf Of Landin, Mark
> Sent: Friday, August 20, 2004 1:16 PM
> To: thin@xxxxxxxxxxxxx
> Subject: [THIN] Re: Ghosting HP DL 380s
>
>
> Why aren't you using it in Gig mode?
>
> Duplex shouldn't make a huge difference anyway, since
> Ghosting is typically a "one-way" operation .. . you are
> either SENDING a huge image TO somewhere else, or RECEIVING a
> huge image FROM somewhere else. There shouldn't be a whole
> lot of two-way traffic during a Ghost procedure.
>
> >
> > I need to image some HP DL380s that come with the HP NC7760 Gigabit
> > Server Adapter with uses the Q57.DOS NDIS driver.
> > Can anyone help me out in determining the switches to use that will
> > allow me to use 100 Full Duplex.
> > It defaults to 100 Half and it is far too painful to wait
> and wait and
> > wait..... Thanks!
> >
> ********************************************************
> This Weeks Sponsor RTO Software
> Do you know which applications are abusing your CPU and memory?
> Would you like to learn? -- Free for a limited time!
> Get the RTO Performance Analyzer to quickly learn the
> applications, users, and time of day possible problems exist.
> http://www.rtosoft.com/enter.asp?id20
> **********************************************************
> Useful Thin Client Computing Links are available at:
> http://thin.net/links.cfm
> ***********************************************************
> For Archives, to Unsubscribe, Subscribe or set Digest or
> Vacation mode use the below link:
> http://thin.net/citrixlist.cfm
>
> ********************************************************
> This Weeks Sponsor RTO Software
> Do you know which applications are abusing your CPU and memory?
> Would you like to learn? -- Free for a limited time!
> Get the RTO Performance Analyzer to quickly learn the
> applications, users, and time of day possible problems exist.
> http://www.rtosoft.com/enter.asp?id=320
> **********************************************************
> Useful Thin Client Computing Links are available at:
> http://thin.net/links.cfm
> ***********************************************************
> For Archives, to Unsubscribe, Subscribe or set Digest or
> Vacation mode use the below link:
> http://thin.net/citrixlist.cfm
>
********************************************************
This Weeks Sponsor RTO Software
Do you know which applications are abusing your CPU and memory?
Would you like to learn? -- Free for a limited time!
Get the RTO Performance Analyzer to quickly learn the applications,
users, and time of day possible problems exist.
http://www.rtosoft.com/enter.asp?id20
**********************************************************
Useful Thin Client Computing Links are available at:
http://thin.net/links.cfm
***********************************************************
For Archives, to Unsubscribe, Subscribe or
set Digest or Vacation mode use the below link:
http://thin.net/citrixlist.cfm
********************************************************
This Weeks Sponsor RTO Software
Do you know which applications are abusing your CPU and memory?
Would you like to learn? -- Free for a limited time!
Get the RTO Performance Analyzer to quickly learn the applications,
users, and time of day possible problems exist.
http://www.rtosoft.com/enter.asp?id20
**********************************************************
Useful Thin Client Computing Links are available at:
http://thin.net/links.cfm
***********************************************************
For Archives, to Unsubscribe, Subscribe or
set Digest or Vacation mode use the below link:
http://thin.net/citrixlist.cfm
Other related posts:
