I don't have a PDF but I save this from a post from Bob Watermen. Hope it helps. Jerry Alpha 21 Electronics Granite City, IL 62040 Ph. 618-452-8620 Fax 618-876-5157 www.alpha21century@xxxxxxxxxxxxx After doing alignments in this service mode press the 7 key on remote TWICE to save to EEPROM Then exit menu by powering off tv Robert tvservice@xxxxxxxxxxxxx H & H Electronics Inc Dallas, TX --------------------------------------------------------------- Text pasted from WinSTIPS 2.0 http://www.ServiceSoftware.com --------------------------------------------------------------- TOSHIBA TZ50V51 Convergence (Blue) Out At Upper Left Corner Only. Similar To Tz50v61. Enter Service Mode. With Tv On. Press , Mute On Remote. Press Mute Again , Continue Pressing Mute And Press Menu On Tv. An "S" Should Be On The Screen. Press Menu To Enter Into Service Mode. Buttons 1 Through 7 Are The Different Selections. Press 7 For Convergence Selection. 2 Button Move Up 3 Change Color 4 Move Left 5 Curser Blink On/Off (Blink = Move Curser Into Position) (Not Blinking = Adjust Mode) 6 Right 7 Adj Mode On/Off (Press 7 To Enter Changes) 8 Down Press Pwr To Exit "Phillip R. Hull" <phil245@xxxxxxxxxxxxx> wrote:I sent you a MAX file for adjustments in service menu, if you can't open it let me know or maybe someone can send him a pdf. Phillip R Hull STET phil245@xxxxxxxxxxxxx FAX 517--569-3075 Professional Technicians only ----- Original Message ----- From: "Phillip R. Hull" To: Sent: Tuesday, May 11, 2004 12:39 PM Subject: [TechAssist] Re: toshiba 50A50 chassis TAC0051 convergence problems > Didn't you try to adjust it the the service menu?? > Phillip R Hull STET > phil245@xxxxxxxxxxxxx > FAX 517--569-3075 > Professional Technicians only > ----- Original Message ----- > From: "markbrock" > To: > Sent: Tuesday, May 11, 2004 10:00 AM > Subject: [TechAssist] Re: toshiba 50A50 chassis TAC0051 convergence problems > > > > Your probably right Philip, I'm hoping that as a last resort only, do you > > have the access to service menu? If its inside the dcu I'm settin aside > as > > customer gave me the set, 300 was his max ? go figure, only 2 years > old.. > > its just the blue pincushion vertical that I'm needing to adjust, but > since > > there is no movement in the customer menu for up and down I'm sure its a > DCU > > issue. > > brock > > > > ----- Original Message ----- > > From: "Phillip R. Hull" > > To: > > Sent: Friday, May 07, 2004 9:43 AM > > Subject: [TechAssist] Re: toshiba 50A50 chassis TAC0051 convergence > problems > > > > > > > These sets had DCU units go bad. remove and check solder first > > (Digital > > > convergence unit) > > > Phillip R Hull STET > > > phil245@xxxxxxxxxxxxx > > > FAX 517--569-3075 > > > Professional Technicians only > > > ----- Original Message ----- > > > From: "markbrock" > > > To: > > > Sent: Friday, May 07, 2004 8:12 AM > > > Subject: [TechAssist] Re: toshiba 50A50 chassis TAC0051 convergence > > problems > > > > > > > > > > Yep, I saw that and a couple others near the same model but I can't > > > > convince myself its one of the stk's, I guess I'll change the other > > stk, > > > > and find out, not sure what a yoke problem would do, there usually > bad, > > > or > > > > get warm, not shorted but possibly windings have crossed between > > varnish, > > > > its an odd problem and since the lines are curved I keep pushing for > it > > > > being before the yoke, but can't adjust up and down convergence. > > wonder > > > > if the stk I put in was bad off the shelf ? thanks Jeff, I'll put > the > > > > model and chassis in the subject line, next time and let you know what > I > > > > find. > > > > brock > > > > > > > > ----- Original Message ----- > > > > From: "Intrepid Video Support" > > > > To: > > > > Sent: Thursday, May 06, 2004 4:53 PM > > > > Subject: [TechAssist] Re: toshiba 50A50 chassis TAC0051 convergence > > > problems > > > > > > > > > > > > > Brock... > > > > > From Tech Repair CD: > > > > > Toshiba\61HX70 TAC0069\Bad Convergence Especially At Bottom (picture > > Is > > > > Full Screen - Good Color And > > > > > Sound)\Picture is pulsing/fluttering rapidly and is sort of divided > up > > > > (vertically) by odd* horizontal > > > > > portions of the picture itself\\TAC0069\STK392-110 ICs\\\\\\\\ > > > > > > > > > > Usually one IC is for blue, the other is for red. > > > > > > > > > > Also...please place the mode and circuit in the subject line. Makes > it > > > > easier for us when searching the > > > > > archives. > > > > > Jeff > > > > > -- > > > > > Intrepid Video TV/VCR Repair > > > > > 263 S Front St, Steelton PA 17113 > > > > > 717-939-7708; (F) 717-564-4952 > > > > > www.intrepid-video.com www.tech-repair.net > > > > > ----- Original Message ----- > > > > > From: "markbrock" > > > > > To: > > > > > Sent: Thursday, May 06, 2004 4:02 PM > > > > > Subject: [TechAssist] toshiba convergence problems > > > > > > > > > > > > > > > model 50A50 chassis TAC0051, fuse 851 blown, R7716 burnt on > > convergence > > > > bd, > > > > > changed stk329110 and fuse and put in 2.2 ohm for R7716 ? not real > > > sure. > > > > > looks like it compared to other convergence ic R's, now comes up > > with > > > > blue > > > > > convergence bad, it appears that the convergence ic I changed is > for > > > blue > > > > ? > > > > > I can move the cursor left and right in menu to move the cross hatch > > but > > > > not > > > > > up and down? do these two conv. IC's work in conjunction ? not > > really > > > > pin > > > > > coushion, as not symmetrical but won't adjust up and down at 9 > points, > > > am > > > > I > > > > > fighting yoke problem? any help appreciated > > > > > brock > > > > > Brock Electronics > > > > > R.R.4 box 237 > > > > > 5208 cr.3385 > > > > > Independence Ks. 67301 > > > > > 620-331-0235 > > > > > fax 331-7191 > > > > > > > > > > markbrock@xxxxxxxxxxxxx > > > > > Zenith*Philips*Peavey*Fender*Crate > > > > > we work on all brands,makes,models > > > > > of anything that plugs in the wall > > > > > > > > > > > > > > > > > > > > > -------------------------------------------------------------------------- > > > > --- > > > > > Lost Password: > > > > > http://www.tech-assist.org and select "Login Problems?". > > > > > Email Archives: > > > > > //www.freelists.org/archives/techassist/ > > > > > > > > > > > > > > > > > > > > > > > > > > -------------------------------------------------------------------------- > > > > --- > > > > > Lost Password: > > > > > http://www.tech-assist.org and select "Login Problems?". > > > > > Email Archives: > > > > > //www.freelists.org/archives/techassist/ > > > > > > > > > > > > > > > -------------------------------------------------------------------------- > > > --- > > > > Lost Password: > > > > http://www.tech-assist.org and select "Login Problems?". > > > > Email Archives: > > > > //www.freelists.org/archives/techassist/ > > > > > > > > > > > > > > > > > > -------------------------------------------------------------------------- > > --- > > > Lost Password: > > > http://www.tech-assist.org and select "Login Problems?". > > > Email Archives: > > > //www.freelists.org/archives/techassist/ > > > > > > -------------------------------------------------------------------------- > --- > > Lost Password: > > http://www.tech-assist.org and select "Login Problems?". > > Email Archives: > > //www.freelists.org/archives/techassist/ > > > > > > > -------------------------------------------------------------------------- --- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ > > ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/