[TechAssist] Re: Philips 55PP9401 (PP15 chassis) convergence troubles
- From: "Gemini Computer & TV" <geminitv@xxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Wed, 25 May 2005 09:20:31 -0400
Philips projo model
55PP9401
60PP9401
This is a PP-15 Philips Chassis Designation.
It's based on the DP-15 Hitachi Chassis.
Different Micro.
Hitachi DP-15 Model
53UDX10B
DCU Crosshatch Phase Adjustment
Adjustment Preparation
1. The Cutoff Adjustment should be completed.
2. Video Controls: Brightness to 90%; Contrast to maximum.
Adjustment Procedure (Normal Mode)
1. Input an NTSC signal.
2. Press the Service Only switch on the Convergence board to enter the
Digital Convergence Adjustment Mode (DCAM).
3. Place the remote control transmitter into the Digital Convergence
Adjustment (DCA) Mode by removing a battery, pressing and holding the 7 and
9 keys, and replacing the battery.
Display Remote Control Diagram
Note: When the remote control transmitter is in DCAM, the TV button will not
illuminate.
Note: The remote control transmitter will time out of DCAM in approximately
20 seconds.
4. Press the Help key on the remote control transmitter. A green crosshatch
will appear.
5. Press the Exit key (this is the Phase Adjustment Mode).
6. Adjust the data value using the keys specified in the chart below so that
the data value corresponds to the chart value.
Saving Data Values
7. Press the Help key to exit Phase Mode.
8. Press the PIP (-) key twice to store the information.
9. When green dots are displayed, press the Mute key.
Adjustment Procedure (1080i HD Mode)
10. Change to 1080i HD Mode. Press the Exit key five times to exit to video
mode.
11. Change the remote control transmitter to TV mode by removing and
replacing a battery.
12. Input a 1080i signal, select that input, bring up the Customer Menu,
select Format, and select 1080i HD mode.
13. Press Exit to leave the Customer Menu.
14. Press the Service Only switch to return to the DCU grid..
15. Place the remote control transmitter into the DCA Mode by removing a
battery, pressing and holding the 7 and 9 keys, and replacing the battery.
16. Repeat steps 4 through 9 above, using the appropriate data values from
the chart below for 1080i Mode.
17. Press the Service Only switch to return to Normal Video Mode.
Data Value Chart
Phase Mode Display Format Display Format
Normal 1080i HD
Adjust Using Address Data Value Address Data Value
4 and 6 keys
on remote control PH-H BF PH-H BF
2 and 5 keys
on remote control PH-V 07 PH-V 07
cursor left and right
on remote control CR-H 4C CR-H 4C
cursor up and down
on remote control CR-V 0C CR-V 0C
Chassis Horizontal Phase (Coarse) Adjustment
Adjustment Preparation
1. Video Controls: Brightness to 90%; Contrast to maximum.
Adjustment Procedure (Normal Mode)
1. Input an NTSC crosshair signal.
2. Set the screen format to Normal.
3. Press the Service Only switch on the Convergence board and display the
digital convergence crosshatch pattern.
4. Mark the center of the digital convergence crosshatch pattern with a
small piece of tape, or hold a finger at the center of the pattern.
5. Press the Service Only switch to return to Normal Mode.
6. Enter the I2C Service Menu, select item H POSI, and adjust the data value
so that the center of the video matches the marked location.
7. Exit the I2C Service Menu.
Adjustment Procedure (16 x 9 Mode)
Note: The I2C Service Menu cannot be entered in the 16 x 9 HD Mode.
8. Input any 1080i (2.14H) signal.
9. Change the screen format to 16 x 9 HD Mode.
10. Press the Service Only switch on the Deflection board and display the
digital convergence crosshatch pattern.
11. Mark the center of the digital convergence crosshatch pattern with a
small piece of tape, or hold a finger at the center of the pattern.
12. Press the Service Only switch to exit the digital convergence crosshatch
pattern.
13. Turn the set's power off and back on, or change the screen format to
Normal.
14. Enter the I2C Bus Alignment Menu and select item 9, H POSI.
Note: To enter the I2C Bus Alignment Menu with power off, press and hold the
Source button, then press and release the Power button.
15. Press the Select key on the remote control transmitter to change to HD
Mode. The H POSI option will change to H POSI H, so that the 16 x 9 Mode
data values may be changed.
16. Adjust the data value slightly.
17. Exit from the I2C Menu.
18. Change the screen format to 16 x 9 Mode.
19. Confirm that the center of the video matches the marked location of the
center of the crosshatch determined in step 11.
20. If the horizontal position is not yet correct, repeat steps 8 through
19.
Raster Tilt Adjustment
Adjustment Preparation
1. The set may face any direction.
2. Input a crosshatch signal.
3. All video controls should be set to their factory preset levels.
4. The screen format should be Normal.
5. The lens focus and electrical focus coarse adjustments should be
complete.
6. The Digital Convergence RAM should be cleared by turning the power off,
pressing and holding the Service Only switch on the Convergence board, then
pressing the Power button.
Adjustment Procedure (Green)
1. Cover the red and blue lenses or short circuit the two pin subminiature
connectors (PTS) on the Red and Blue CRT boards to produce only green.
2. Turn the Green Deflection Yoke to adjust the tilt so that the green line
is level (+/- 2mm tolerance). Refer to the Tilt Adjustment Diagram.
Display Tilt Adjustment Diagram
Adjustment Procedure (Red)
3. Remove the cover or PTS short circuit from the red CRT and align the red
line with the green line (+/- 1mm tolerance). Refer to the Tilt Adjustment
Diagram.
Adjustment Procedure (Blue)
4. Remove the cover or PTS short circuit from the blue CRT, replace the red
CRT's cover or PTS short, and align the blue line with the green line (+/-
1mm tolerance). Refer to the Tilt Adjustment Diagram.
Adjustment Procedure (Completion)
5. Tighten the Deflection Yoke screws to approximately 12kg-cm +/- 2kg-cm.
6. Remove all covers or PTS short circuits.
7. Turn the power off.
Beam Alignment
Adjustment Preparation
1. The preheat run should be complete.
2. The DCU Phase Data Adjustment should be complete.
3. The H POSI (Coarse) Adjustment should be complete.
4. The Raster Tilt Adjustment should be complete.
5. The Brightness Control should be set to 90%; the Contrast Control should
be set to maximum.
6. Input a crosshatch signal or dot pattern.
7. The screen format should be set to Progressive Mode.
Adjustment Procedure
1. Short circuit the two pin subminiature connectors (PTS) on the Red and
Blue CRT boards to produce only green.
2. Place the green tube beam alignment magnets in the cancel state as shown
in the diagram.
Display Cancel State Magnet Position Diagram
3. Turn the Green Static Focus VR fully counterclockwise, and mark the
center position of the crosshatch on the screen.
4. Turn the Green Static Focus VR fully clockwise.
5. Rotate the two Green Beam Alignment Magnets to move the center of the
crosshatch back to the marked position. Refer to the Magnet Location
Diagram.
Display Magnet Location Diagram
6. If the image position does not shift when the Green Static Focus VR is
turned, the green adjustment is complete.
7. If the image position moves, repeat steps 2 through 6.
8. Perform the beam alignments for red and blue in the same manner as
described above for green, using the appropriate magnets and Focus VRs.
9. When all beam alignments have been completed, place a small strip of
paint on the beam alignment magnets to ensure they remain in place.
Red and Blue Raster Offset Adjustment
Raster offset is necessary to conserve memory allocation. It is important to
remember that the red is offset left of center, while blue is offset right
of center. Refer to the overlay dimensions for additional information.
Adjustment Preparation
1. With power off, press the Service Only switch on the Convergence board.
While holding the switch down, press and release the power switch to turn on
the power. The DCU grid will appear without convergence correction. Note
that after entering DCAM, with each press of the Service Only switch, the
picture will toggle between Video Mode and the DCU grid.
2. The video controls should be at their factory preset levels.
3. The Static Focus Adjustment should be complete.
Adjustment Procedure
1. Use the red, green, and blue centering magnets to adjust the crosshatch
pattern so that it conforms to the offset diagram (DCU data is cleared).
2. With a 4 x 3 aspect ratio, green is centered, red is offset 15mm to the
left of center, and blue is offset 25mm to the right of center. The
tolerance for all horizontal offsets is +/- 2mm. All vertical positions
should be geometrically centered on the screen.
Display Offset Diagram
Vertical Size Adjustment
Adjustment Procedure
1. Install the correct overlay and input an NTSC signal.
2. With power off, press the Service Only switch on the Convergence board.
Hold the switch down, press and release the Power switch. The DCU grid will
appear without convergence correction. Note that after entering DCAM, with
each press of the Service Only switch, the picture will toggle between Video
Mode and DCU grid.
3. Select Green (A/CH) and press the Menu button to remove red and blue.
4. Adjust R607 (Vertical Size Adjustment VR) to match the marks on the
overlay. Refer to the Vertical Size Diagram. Turn off the power to exit
DCAM.
Display Vertical Size Diagram
Notes: The centering magnets may be moved to facilitate the adjustment.
Distance is important, not centering. The vertical frequency is shared
between Normal and 16 x 9 HD Modes.
Alternate Method
1. Adjust R607 to obtain distance l (in the Vertical Size Diagram) of 730mm
+/- 5mm for 55" sets, or 800mm +/- 5mm for 60" sets.
Horizontal Size Adjustment
Adjustment Preparation
1. Install the correct overlay and input an NTSC signal.
2. With power off, press the Service Only switch on the Convergence board.
Hold the switch down, press and release the Power switch. The DCU grid will
appear without convergence correction. Note that after entering DCAM, with
each press of the Service Only switch, the picture will toggle between Video
Mode and DCU grid.
3. Select Green (A/CH) and press the Menu button to remove red and blue.
Adjustment Procedure
1. Adjust R711 (Horizontal Size Adjustment VR) to match the marks on the
overlay. Refer to the Horizontal Size Diagram.
2. Turn off the power to exit DCAM.
Display Horizontal Size Diagram
Alternate Method
1. Adjust R711 to obtain distance l (in the Horizontal Size Diagram) of
1060mm +/- 5mm for 55" sets, or 1155mm +/- 5mm for 60" sets.
Beam Form (Shape) Adjustment
Adjustment Preparation
1. The preheat run should be complete.
2. The following adjustment procedures should be complete: Cutoff,
Pre-optical Focus, DCU Phase Data, Horizontal Position (Coarse), Raster
Tilt, Beam Alignment, Raster Position, Vertical Size, and Horizontal Size.
3. The Brightness Control should be set at 90%; the Contrast Control should
be set to maximum.
4. Input an NTSC dot signal.
Adjustment Procedure
1. For the green CRT beam shape adjustment, short circuit the two pin
subminiature connectors on the red and blue CRT boards to project only the
green beam.
2. Turn the Green Static Focus VR fully clockwise.
3. Adjust the green 4-pole magnets (refer to the Magnet Location Diagram) to
make the dot at the center of the screen a true circle. Refer to the Beam
Shape Diagram.
Display Magnet Location Diagram
Display Beam Shape Diagram
4. Follow the procedure outlined in steps 1 through 3 above for both the red
and blue CRT beams.
5. When all beams have been adjusted, return the Green, Red, and Blue Static
Focus VRs to their best focus points.
Lens Focus Adjustment
Adjustment Preparation
1. The Electrical Focus Adjustment and Tilt Adjustment should be complete.
2. Input a crosshatch pattern signal.
3. Set the Brightness Control to midrange (50%); the Contrast Control to
60% - 70%.
Adjustment Procedure
1. Short the 2-pin subminiature connector(s) on the appropriate CRT board to
remove the colors not being adjusted in order to adjust one color at a time.
The colors may be adjusted in any order.
2. Refer to the Lens Assembly Diagram. Loosen the fixing screw on the lens
assembly so that the lens cylinder can be turned. Take care not to loosen
the screw too much, as that could cause movement of the lens cylinder when
tightening.
Display Lens Assembly Diagram
3. Rotate the cylinder back and forth while observing the crosshatch pattern
at the center of the screen to obtain the best focus point. In order to
access the focus rings on the lenses, first remove the upper and lower back
covers, then remove the cross piece which is secured with four screws.
Replace the upper back cover to which the mirror is mounted. The small
opening allows access the focus rings.
4. After completing the optical focus, tighten the fixing screw.
5. Repeat the process for each of the other colors. Use care when adjusting
the green optical focus, as green is the most dominant gun and any error
will be easily seen.
6. After the adjustment is complete, replace the cross piece and back
covers, then repeat the Electrical Focus Adjustment if necessary.
Static Focus Adjustment
Adjustment Preparation
1. The preheat run should be complete.
Adjustment Procedure
1. Short the 2-pin subminiature connector(s) on the appropriate CRT board to
remove the colors not being adjusted in order to adjust one color at a time.
The colors may be adjusted in any order.
2. Adjust the Focus VR for the appropriate color to achieve optimum focus.
Refer to the Focus Pack Location Diagram.
Display Focus Pack Location Diagram
3. Repeat the procedure for the other two colors.
Blue Defocus Adjustment
Adjustment Preparation
1. The screen format should be Progressive Mode.
2. The Brightness Control should be set to 90%; the Contrast Control to
maximum.
Adjustment Procedure
1. Input an NTSC crosshatch pattern signal.
2. Turn the Blue Focus VR fully clockwise. Refer to the Focus Pack Location
Diagram.
Display Focus Pack Location Diagram
3. Adjust the blue defocus to 1mm on each side, equaling 2mm total. Refer to
the Blue Defocus Diagram.
Display Blue Defocus Diagram
White Balance and Sub-Brightness Adjustment
Adjustment Conditions
1. The Cutoff and Blue Defocus Adjustments should be complete.
2. High brightness white balance; low brightness white balance.
3. The Screen Adjustment VRs are on the Focus Pack.
Display Focus Pack Diagram
4. The Drive Adjustment is performed using the I2C Bus Alignment within the
Service Menu.
Adjustment Preparation
1. Begin the adjustment procedure at least 20 minutes after turning on power
to the set.
2. Adjust the brightness and black level OSD to minimum, using the remote
control transmitter.
3. Tune to any channel, though a B/W signal would be best.
4. Use the I2C Service Menu to set the drive adjustment registers to
midrange (3F).
5. Use the Customer Menu to set the Color Temperature to Cool.
Note: When adjusting the Screen Controls after the Cutoff Adjustment has
been completed, never turn the controls clockwise, as this shortens the life
of the CRTs. Always adjust the Screen Controls counterclockwise following
completion of the Cutoff Adjustment.
Adjustment Procedure
1. Enter the I2C Adjustment Mode. With power off, press the Source and Power
buttons at the same time, then release. The Service Menu should be
displayed.
2. Adjust the Sub-Brightness (Number 2 SUBBRT), using the I2C bus alignment
procedure so that only the slightest white portions of the raster can be
seen.
3. Exit the Service Menu by pressing the Menu button.
4. Input a grayscale signal into any video input and select that input,
using the Source button on the remote control transmitter or front control
panel.
5. Turn the Brightness and Contrast OSD all the way up.
6. Enter the Service Menu again.
7. Make the white areas as white as possible, using the Red DRV (Cool) and
Green DRV (Cool) Drive Adjustment within the I2C Service Menu.
8. Set the Brightness and Contrast to minimum.
9. Adjust the low brightness area to black and white, using the Screen
Adjustment VRs (red, green, and blue) on the Focus Pack Assembly.
10. Check the high brightness white areas again. If readjustment is needed,
repeat steps 6 through 9. If not, press the Menu key on the remote control
transmitter to exit the Service Menu.
Sub-Picture Amplitude Adjustment
Adjustment Preparation
1. The Sub-Brightness Adjustment should be complete.
2. Begin the adjustment procedure at least 20 minutes after turning on power
to the set.
3. Set Contrast to maximum; Brightness to midrange.
4. Press PinP button on the remote control transmitter; PiP should appear on
the screen.
5. Select Single Mode.
6. Input an NTSC white signal for the Main Picture and Sub Picture (do not
use component signals).
7. Connect an oscilloscope probe to P852 on the Green CRT board to check the
sub-picture amplitude.
Adjustment Procedure
1. Enter the I2C Adjustment Mode.
2. Press the Menu button on the remote control transmitter to scroll through
the adjustment menu pages, until TA1270-M appears at the top of the screen.
Display TA1270-M Screen
3. Press the PIP CH button on the remote control transmitter to change to
the TA1270-S screen.
Display TA1270-S Screen
4. Monitor the oscilloscope display (P852) and change the SUB CNT data
register value to equalize the amplitude of the sub picture level and the
main picture level as shown in the diagram.
Display Picture Level Diagram
5. Exit the Service Menu.
Horizontal Phase (Fine) Adjustment
Adjustment Preparation
1. Set Contrast Control to maximum; Brightness Control to 90%.
Adjustment Procedure (Normal Mode)
1. Input an NTSC crosshair signal.
2. Set screen format to Normal Mode.
3. Press the Service Only switch on the Convergence board to display the
digital convergence crosshatch pattern.
4. Mark the center of the digital convergence crosshatch pattern with a
small piece of tape, or hold a finger at the center of the pattern, then
press the Service Only switch to return to Normal Mode.
Note: To enter the I2C Bus Alignment Menu, turn off power to the set, press
and hold the Source button, then press and release the Power button.
5. Enter the I2C Bus Alignment Menu, select H POSI, and adjust the data
value so that the center of the video corresponds to the marked location.
6. Exit from the I2C Menu.
Adjustment Procedure (16 x 9 HD Mode)
7. Input a 1080i (2.14H) signal.
8. Change the screen format to 16 x 9 Mode.
9. Press the Service Only switch on the Deflection board to display the
digital convergence crosshatch pattern.
10. Mark the center of the digital convergence crosshatch pattern with a
small piece of tape, or hold a finger at the center of the pattern, then
press the Service Only switch to return to Normal Mode.
11. Turn the power off and back on.
12. Enter the I2C Bus Alignment Menu and select H POSI.
13. Press the Select key on the remote control transmitter to change to HD
mode. The H POSI item should change to H POSI H, so the data for the 16 x 9
HD mode may be changed.
14. Adjust the data value slightly.
15. Exit from the I2C Menu.
16. Change the screen format to 16 x 9 Mode.
17. Confirm that the center of the video corresponds to the center of the
DCU crosshatch pattern marked in step 10.
18. If the Horizontal Position is not correct, repeat steps 7 through 17
until the center position is correct.
DCU Intellisense Character Setup
Note: This adjustment is only necessary when a new DCU is being applied. The
DCU should be set to 99 for Philips INTELLISENSE.
Adjustment Preparation
1. Input an NTSC, RF, or video signal.
2. With power off, press and hold the Service Only button on the
Convergence/Focus board, press the Power button until a picture appears,
then release both buttons. The picture will be displayed without convergence
correction data. Press the Service Only button to bring up the internal
crosshatch pattern.
Adjustment Procedure (Normal Mode)
1. Change the remote control transmitter to DCU Mode by removing one
battery, pressing and holding the 7 and 9 keys, and replacing the battery.
Note that the TV light does not illuminate in DCU Mode.
2. Press the Freeze key on the remote control transmitter. One additional
line should appear near the top and near the bottom.
3. Press the oval Source button to display the ADJ. PARAMETER Mode as shown.
ADJ. PARAMETER
--> ADJ. DISP. : 99
SEL. STAT. : 00
DEMO. WAIT : 2f
4. If necessary, use the cursor left or right keys to change the ADJ. DISP.
data value to 99.
5. Use the cursor up and down keys to scroll through the ADJ. PARAMETER
settings. Confirm that the data values are identical with those listed in
the table below. If necessary, use the cursor left and right keys to change
the register values to correspond with those in the table.
Parameter Normal Squeeze
ADJ. DISP 99 -
SEL. STAT 00 -
DEMO WAIT 2f -
INT STEP 1 02 -
INT A DLY 0a -
INT C DLY 0a 5a
INT BAR 1c -
MGF STEP 1 00 -
MGF A DLY 0a -
MGF C DLY 0a 5a
MGF BAR 0e -
SENSOR CK 00 -
SENSOR 0 ff -
SENSOR 1 00 -
SENSOR 2 ff -
SENSOR 3 01 -
SENSOR 4 ff -
SENSOR 5 06 -
SENSOR 6 ff -
SENSOR 7 07 -
AD LEVEL 03 -
E. DISPLAY 00 -
ADJ. TIMS 60 -
AD LEVEL 05 -
AD NOISE 80 -
PHASE MOT 60 -
H. BLK-RV 06 03
H. BLK-GV 01 -
H. BLK-BV 06 03
H. BLK-H 00 -
PON DELAY 0c -
IR-CODE 00 -
INITIAL 50 9e -
MGF 50 96 -
9 POINT 50 fe -
STAT 50 fe -
DYNA 50 9f -
6. Press the PIP CH (-) key twice to write the changed data values into
EEPROM. Pressing the PIP CH (-) once will display the message "? ADJ.
PARAMETER? ROM WRITE ?" and the second press confirms that the new values
will be written to EEPROM. Green dots appear after the operation is
complete.
7. Press the Mute button three times to exit.
Adjustment Procedure (16 x 9 Mode)
8. Input a 1080i signal.
9. Press the Exit key on the remote control transmitter five times to exit
to the Video Mode.
10. Change the remote control transmitter to TV Mode by removing and
replacing one battery. Note that the TV light now illuminates.
11. Change the input to 1080i Mode.
12. Enter the Customer Menu, select FORMAT, and change to 16 x 9 HD Mode.
13. Exit the Customer Menu.
14. Press the Service Only switch to return to DCAM.
15. Change the remote control transmitter to DCU Mode by removing one
battery, pressing and holding the 7 and 9 keys, and replacing the battery.
Note that the TV light does not illuminate in DCU Mode.
16. Repeat steps 2 through 7 above for 16 x 9 Mode.
17. Turn off power to the set.
DCU Intellisense Pattern Setup
Note: This adjustment is only necessary when a new DCU is being applied.
Each model has a specific setup pattern position.
Adjustment Preparation
1. Input an NTSC, RF, or video signal.
2. With power off, press and hold the Service Only button on the
Convergence/Focus board, press the Power button until a picture appears,
then release both buttons. The picture will be displayed without convergence
correction data. Press the Service Only button to bring up the internal
crosshatch pattern.
Adjustment Procedure (Normal Mode)
1. Change the remote control transmitter to DCU Mode by removing one
battery, pressing and holding the 7 and 9 keys, and replacing the battery.
Note that the TV light does not illuminate in DCU Mode.
2. Press the Freeze key on the remote control transmitter. One additional
line should appear near the top and near the bottom.
3. Press the Help key to display the PATTERN Mode as shown in the diagram.
Display PATTERN Mode Diagram
4. Use the 6 key to rotate the arrow. The arrow rotates clockwise one
position with each press of the 6 key.
5. Use the following keys to switch color patterns: A/CH - Green; 0 - Red;
Round Source: Blue.
6. Press the cursor left or right key to change the pattern position data in
the horizontal direction. Press the cursor up or down key to change the
pattern position data in the vertical direction.
7. Set the data values as shown in the chart below.
Normal Mode
0
1
2
3
4
5
6
7
RH
X
02
X
fa
X
02
X
04
RV
X
00
X
00
X
02
X
00
GH
X
00
X
fa
X
00
X
04
GV
X
00
X
00
X
02
X
00
BH
X
00
X
fa
X
00
X
04
BV
X
00
X
00
X
02
X
00
8. Press the PIP CH (-) key twice to write the changed data values into
EEPROM. Pressing the PIP CH (-) once will display the message "? ADJ.
PARAMETER? ROM WRITE ?" and the second press confirms that the new values
will be written to EEPROM. Green dots appear after the operation is
complete.
9. Press the Mute button three times to exit.
Adjustment Procedure (16 x 9 Mode)
10. Change the display to 16 x 9 Mode.
11. Press the Exit key on the remote control transmitter five times to exit
to the Video Mode.
12. Change the remote control transmitter to TV Mode by removing and
replacing one battery. Note that the TV light now illuminates.
13. Change the input to 1080i Mode.
14. Enter the Customer Menu, select FORMAT, and change to 16 x 9 HD Mode.
The top and bottom panels should now be black.
15. Exit the Customer Menu.
16. Change the remote control transmitter to DCU Mode by removing one
battery, pressing and holding the 7 and 9 keys, and replacing the battery.
Note that the TV light does not illuminate in DCU Mode.
17. Press the Service Only switch to return to DCAM.
18. Repeat steps 2 through 9 above for 16 x 9 Mode, using the data values
shown in the chart below.
16 x 9 HD Mode: V. Squeeze Activated
0
1
2
3
4
5
6
7
RH
X
02
X
fa
X
02
X
06
RV
X
00
X
00
X
02
X
00
GH
X
00
X
fa
X
00
X
06
GV
X
00
X
00
X
02
X
00
BH
X
00
X
fa
X
00
X
06
BV
X
00
X
00
X
02
X
00
19. Turn off power to the set.
Bob Waterman, CET® #RI-28
Master Technician License #9109
Service Manager / Parts Manager
Gemini Computer, TV, & Security Alarms
(508)695-7302
(508)695-7769 FAX
geminitv@xxxxxxxxxxx
To: <techassist@xxxxxxxxxxxxx>
Sent: Tuesday, May 24, 2005 10:32 AM
Subject: [TechAssist] Philips 55PP9401 (PP15 chassis) convergence troubles
> Assisting another local shop.( he says this is really an Hitachi
> chassis) Here is his info as told to me:
> "Came in with resistor RK54 burnt. He replaced that along with blue
> convergence IC IK05. When going thru auto convergence, TV does not
> respond, but RK54 stays good (auto convergence called Intellisense)
> On the converg. module,push "service only" button, crosshatch
> appears.Need to knowof any way to converge,or if a problem still exists
> with convergence board, Checking on a service manual, need desparately."
> I guess he is askingithat since he replaced the burnt resistor and
> associated blue converg. STK IC, is he not accessing the convergence
> alignment area pproperly, or is there an actual problem. he says the
> Intellisense doesn't appear to work.All I have.
> Phil Bader
>
> --
>
> Philip Bader
> Jan Phyl TV Inc. (estab. 1976)
> 3420 Recker Hwy. Winter Haven, Fl. 33880
> Fax (863) 299-8821
> email: tjanphyl@xxxxxxxxxxxxxxx
-----------------------------------------------------------------------------
This Email List is Public. Remove: http://www.tech-assist.org/remove.htm
Lost Password: http://www.tech-assist.org and select "Login Problems?".
Appliance Repair List: http://www.tech-assist.org/secure/tip/chatjoin.htm#app
Email Archives: //www.freelists.org/archives/techassist/
Other related posts:
