Tks J for all the good info..regards..Don of HARTS-TVCR''ASC'' 9-Robert St.,Oromocto,NewBrunswick,CAN Tel#506-357-9785Fax#506-357-6010 ----- Original Message ----- From: "J Silverman" <greentron@xxxxxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, January 24, 2002 3:25 PM Subject: [TechAssist] Re: Fw: Symphonic-VCRmodSE426G,fccADTVCR226G > > Its one of two things. Either the main lever is not moving the mode lever to > the proper position for reel drive, or the main lever holder is not locking > the reel brakes off during unload. We usually replace the main lever and > main lever holder to take care of many problems. > I once saw a post to drill a hole through the plastic main lever pivot and > put a screw in to compensate for wear of the pivot, but I have never tried > that. > When the main lever holder is the problem, it usually leaves the reel brakes > on in FF/REW too. You can usually see a slot cut into the main lever holder > by rubbing on the main lever. > Once, replacing the parts did not help on the reel drive problem and I had > to bend the end of the main lever over about 1/16 inch at the mode lever to > get it to work. > Jerry Silverman > Greentron Inc > 4 Newland Ave > Greenville SC 29609 > 864 232 3889 > Fax 271 2080 > mailto:greentron@xxxxxxx > ----- Original Message ----- > From: "Don Hartigan" <hartstv@xxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Thursday, January 24, 2002 12:10 AM > Subject: [TechAssist] Fw: Symphonic-VCRmodSE426G,fccADTVCR226G > > > > > > HARTS-TVCR''ASC'' > > 9-Robert St.,Oromocto,NewBrunswick,CAN > > Tel#506-357-9785Fax#506-357-6010 > > ----- Original Message ----- > > From: Don Hartigan > > > > Sent: Thursday, January 24, 2002 1:08 AM > > Subject: Symphonic-VCRmodSE426G,fccADTVCR226G > > > > > > It's twin,Citizen mod#JVHS3992,have the same problem.Upon ejecting there > is a small amount of tape left hanging out .The supply reel is not fully > retracting tape back into cassette holder.Replaced led,sensors,mode > switch,belts,retimed master cam gear,mode sw&they are right on.It seems the > supply reel does not want to make that extra couple of turns to completely > retract tape back into cassette holder.I've done a ton of these clones,but > this one has me stumped.Any suggestions??..Don of > > HARTS-TVCR''ASC'' > > 9-Robert St.,Oromocto,NewBrunswick,CAN > > Tel#506-357-9785Fax#506-357-6010 > > > > ------------------------------------------ > > Make your TechAssist database better! > > Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > > ------------------------------------------ > > To UNSUBSCRIBE your email address, click here: > > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > > Or send a BLANK email with unsubscribe in the > > SUBJECT field to the address above. > > > > > > ------------------------------------------ > Make your TechAssist database better! > Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ > ------------------------------------------ > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > Or send a BLANK email with unsubscribe in the > SUBJECT field to the address above. > ------------------------------------------ Make your TechAssist database better! Submit Repair Tips here: http://www.tech-assist.org/secure/tip/ ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.