[TechAssist] Re: Fw: Panasonics Mod# CTP-2764S (Vertical foldover)
- From: "Shoreline Electronics" <jstielau@xxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Thu, 10 Jun 2004 09:00:44 -0400
Should be as easy as changing all 3 Caps In Vertical Section C455 100uf @
35v, C451 220uf @ 16 V, C458 10uf @ 16v .
Also Change C559 220uf @25v (Off Pin 5 Of Flyback) Also check C576 22uf
@100v
==========================
Jeff Stielau
Shoreline Electronics Repair
344 East Main Street
Clinton,CT 06413
860-399-1861
860-664-3535 (fax)
jstielau@xxxxxxxx
========================
"If you push something hard enough it will fall over."
Fudd's First Law of Opposition - Sir Sidney Fudd
----- Original Message -----
From: "javiles6" <javiles6@xxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Wednesday, June 09, 2004 11:06 PM
Subject: [TechAssist] Fw: Panasonics Mod# CTP-2764S (Vertical foldover)
> techs
>
>
> since i have not receive any reply to this message, what about a voltage
pin
> out for this IC. If i could just get the right voltages i could take it
from
> there. This it why is hard to work without an schematic, and you can not
> charge the customer for this because the labor will be too high. And if
you
> buy the schematic with what you are going to charge for the labor then you
> will only get a profit of perhaps $20.00 to $30.00 dollars. So any help is
> appreciated.
>
> Thanks
>
> Jose
> ----- Original Message -----
> From: "javiles6" <javiles6@xxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Tuesday, June 08, 2004 10:01 PM
> Subject: [TechAssist] Panasonics Mod# CTP-2764S (Vertical foldover)
>
>
> > Hello techs
> > This set came in with a verical line across the middle of the set. I
> resolder the verical IC(IC451) but with no help, so i replace it with an
NTE
> 7085. Now the set is about 4" open but with verical foldover. I have
change
> C455(100uf/35v which was out of tolerance and C451(220uf/16V) but with no
> help. I have the 12V at pin one of IC and the 26v at pin 7, also at pin
12.
> All of the other pin run from 5v to 6v, except pin 10 which GND and pin 9
> OSC BLOCKING. I don`t have an schematic to be certain that this are the
> correct voltages. Does any one have the vertical section that could e-mail
> me or any help that could offer. Your help is always appreciated.
> >
> > Thanks
> >
> > Jose
> >
> > Aviles Computer & TV Repairs
> > 508 Bingaman st
> > Reading, PA 19602
> > Tel # 610-478-1342
> >
>
> --------------------------------------------------------------------------
> ---
> > Lost Password:
> > http://www.tech-assist.org and select "Login Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
>
>
> --------------------------------------------------------------------------
---
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
