[TechAssist] Re: Fw: Panasonics Mod# CTP-2764S (Vertical foldover)
- From: Eric Manuel <tvman@xxxxxxxxxxxxxxx>
- To: techassist@xxxxxxxxxxxxx
- Date: Thu, 10 Jun 2004 14:22:52 -0230
Hi Jose I dont know where it is I got that tip from Repair World Page
Eric
E M Electronics
Deer Lake Nfld
Eric Manuel
javiles6 wrote:
>
> Eric
>
> Since you ask me for the chassis # AREDP204 here it is. Now where is this
> C445 located, i can seem to find it. Unless you mean C455.
>
> Thanks
>
> Jose
> ----- Original Message -----
> From: "Eric Manuel" <tvman@xxxxxxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Thursday, June 10, 2004 5:15 AM
> Subject: [TechAssist] Re: Fw: Panasonics Mod# CTP-2764S (Vertical foldover)
>
> > Hi Jose did you get C453 & C445 Eric
> > E M Electronics
> > Deer Lake Nfld
> > Eric Manuel
> >
> > javiles6 wrote:
> > >
> > > techs
> > >
> > > since i have not receive any reply to this message, what about a voltage
> pin
> > > out for this IC. If i could just get the right voltages i could take it
> from
> > > there. This it why is hard to work without an schematic, and you can not
> > > charge the customer for this because the labor will be too high. And if
> you
> > > buy the schematic with what you are going to charge for the labor then
> you
> > > will only get a profit of perhaps $20.00 to $30.00 dollars. So any help
> is
> > > appreciated.
> > >
> > > Thanks
> > >
> > > Jose
> > > ----- Original Message -----
> > > From: "javiles6" <javiles6@xxxxxxxxxxx>
> > > To: <techassist@xxxxxxxxxxxxx>
> > > Sent: Tuesday, June 08, 2004 10:01 PM
> > > Subject: [TechAssist] Panasonics Mod# CTP-2764S (Vertical foldover)
> > >
> > > > Hello techs
> > > > This set came in with a verical line across the middle of the set. I
> > > resolder the verical IC(IC451) but with no help, so i replace it with an
> NTE
> > > 7085. Now the set is about 4" open but with verical foldover. I have
> change
> > > C455(100uf/35v which was out of tolerance and C451(220uf/16V) but with
> no
> > > help. I have the 12V at pin one of IC and the 26v at pin 7, also at pin
> 12.
> > > All of the other pin run from 5v to 6v, except pin 10 which GND and pin
> 9
> > > OSC BLOCKING. I don`t have an schematic to be certain that this are the
> > > correct voltages. Does any one have the vertical section that could
> e-mail
> > > me or any help that could offer. Your help is always appreciated.
> > > >
> > > > Thanks
> > > >
> > > > Jose
> > > >
> > > > Aviles Computer & TV Repairs
> > > > 508 Bingaman st
> > > > Reading, PA 19602
> > > > Tel # 610-478-1342
> > > >
> > >
> > --------------------------------------------------------------------------
> > > ---
> > > > Lost Password:
> > > > http://www.tech-assist.org and select "Login Problems?".
> > > > Email Archives:
> > > > //www.freelists.org/archives/techassist/
> > >
> >
> > --------------------------------------------------------------------------
> ---
> > > Lost Password:
> > > http://www.tech-assist.org and select "Login Problems?".
> > > Email Archives:
> > > //www.freelists.org/archives/techassist/
> >
> > --------------------------------------------------------------------------
> ---
> > Lost Password:
> > http://www.tech-assist.org and select "Login Problems?".
> > Email Archives:
> > //www.freelists.org/archives/techassist/
>
> -----------------------------------------------------------------------------
> Lost Password:
> http://www.tech-assist.org and select "Login Problems?".
> Email Archives:
> //www.freelists.org/archives/techassist/
-----------------------------------------------------------------------------
Lost Password:
http://www.tech-assist.org and select "Login Problems?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
