[SI-LIST] Re: Skew and Jitter
- From: SI Eng <diggidydog2003@xxxxxxxx>
- To: si-list@xxxxxxxxxxxxx
- Date: Mon, 31 Mar 2003 16:35:09 -0500 (EST)
Todd, Thanks for your response. Correct me if I'm wrong here, but if the issue
is that time 0 wouldn't be identical for Rise and Fall edges, this would apply
to a Spice simulation of the I/O cell as well. If the prop. delays for Rise and
Fall are different through a device, then to set time 0 at the input to the I/O
buffer - where the stimulus is applied - would give an erroneous result when
the Rise and Fall waveforms are merged for an eye diagram. The relative
positions between Rise and Fall would be wrong. One would have to know the
exact delay of Rise vs. Fall of the internal path from the output flop to the
input of the I/O Buffer in order to set the relative position of Rise and Fall
corrrectly. No ? Douglas ----- Original Message ----- From: "Todd Westerhoff"
<twesterh@xxxxxxxxx>To: <si-list@xxxxxxxxxxxxx>Sent: Monday, March 31, 2003
10:28 AMSubject: [SI-LIST] Re: Skew and Jitter
>
> IBIS simulates output behavior only, it doesn't try to predict the behavior
> through the part in question. If you can simulate the pieces of your chain
> individually and then sum the jitter contributions from the pieces, IBIS may
> work for you.
>
> Eye diagrams and IBIS are a special discussion in their own right. You
> should be aware that rising and falling waveforms are usually extracted
> independently for IBIS mnodels, and that "time 0" in the waveform tables is
> not necessarily meaningful (as in, it might be the time the output starts to
> switch, and it might not). If you're going to run pattern simulations and
> look at eye-digrams using IBIS models, you need to be sure that "time 0" is
> correlated across the rising and fallinng waveform table data. If it isn't,
> you could be making assumptions that aren't necessarily valid.
>
> If you have the time and resources to do so, it's worthwhile to study the
> problem using both Spice and IBIS models initially, then move over to IBIS
> if you find good correlation between the two approaches.
>
> Todd.
>
> Todd Westerhoff
> High Speed Design Specialist
> Cisco Systems
> 1414 Massachusetts Ave - Boxboro, MA - 01719
> email:twesterh@xxxxxxxxx
> ph: 978-936-2149
> ============================================
>
> "When did the choices get so hard, with so much more at stake?
> Life gets mighty precious when there's less of it to waste"
>
> - Bonnie Raitt, "Nick of Time"
>
>
> -----Original Message-----
> From: si-list-bounce@xxxxxxxxxxxxx
> [mailto:si-list-bounce@xxxxxxxxxxxxx]On Behalf Of SI Eng
> Sent: Sunday, March 30, 2003 9:39 PM
> To: si-list@xxxxxxxxxxxxx
> Subject: [SI-LIST] Skew and Jitter
>
>
>
> Gurus :
>
> How does one determine the eye diagram at a receiver from simulation using
> IBIS models, when there are multiple devices in the path from the driver ?
> Each device in the path will contribute to the jitter and skew which will
> affect the quality of the eye at the receiver. Does this need to be done
> using Spice ?
>
> Thanks,
>
> Douglas
>
>
>
> ---------------------------------
> Post your free ad now! Yahoo! Canada Personals
>
>
> ------------------------------------------------------------------
> To unsubscribe from si-list:
> si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
>
> or to administer your membership from a web page, go to:
> //www.freelists.org/webpage/si-list
>
> For help:
> si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
>
> List archives are viewable at:
> //www.freelists.org/archives/si-list
> or at our remote archives:
> http://groups.yahoo.com/group/si-list/messages
> Old (prior to June 6, 2001) list archives are viewable at:
> http://www.qsl.net/wb6tpu
>
>
> ------------------------------------------------------------------
> To unsubscribe from si-list:
> si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
>
> or to administer your membership from a web page, go to:
> //www.freelists.org/webpage/si-list
>
> For help:
> si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
>
> List archives are viewable at:
> //www.freelists.org/archives/si-list
> or at our remote archives:
> http://groups.yahoo.com/group/si-list/messages
> Old (prior to June 6, 2001) list archives are viewable at:
> http://www.qsl.net/wb6tpu
>
>
---------------------------------
Post your free ad now! Yahoo! Canada Personals
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List archives are viewable at:
//www.freelists.org/archives/si-list
or at our remote archives:
http://groups.yahoo.com/group/si-list/messages
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
Other related posts:
