Hi Carson,
From an SI-prospective Press-Fit and Through hole perform worst compared to
SMT. Only Mechanical or Production related reasons would be arguments to not
use SMT. Some Military electronics require press-fit or through hole
connectors, SMT is prohibited, and I think that’s the main reason why you can
buy those.
BR
Gert
----------------------------------------
HARTING AG & Co. KG | Postfach 11 33, 32325 Espelkamp | Marienwerderstraße 3,
32339 Espelkamp | www.HARTING.com
Generalbevollmächtigte Gesellschafterin: Dipl.-Hdl. Margrit Harting
Persönlich haftende Gesellschafter:
HARTING WiMa AG (Luxemburg) & Co. KG | Amtsgericht Bad Oeynhausen | HRA 8259 |
Espelkamp, persönlich haftende Gesellschafterin: HARTING Führungs AG (Registre
de Commerce et des Sociétés Luxembourg) | B 170749 | Luxemburg
Vorstand: Dipl.-Kfm. Philip F. W. Harting (Vorsitzender), Dipl.-Kffr. Maresa W.
M. Harting-Hertz, Dipl.-Kfm. Dr.-Ing. E. h. Dietmar Harting, Dr. rer. nat.
Frank Brode, Dipl.-Ing. (FH), Dipl.-Wirtsch.-Ing. (FH) Andreas Conrad, Dr. iur.
Michael Pütz;
HARTING Beteiligungs GmbH & Co. KG | Amtsgericht Bad Oeynhausen | HRA 5599 |
Espelkamp, persönlich haftende Gesellschafterin: HARTING Beteiligungs
Verwaltungs GmbH | Amtsgericht Bad Oeynhausen | HRB 8803 | Espelkamp.
Sitz der Gesellschaft: Espelkamp | Amtsgericht Bad Oeynhausen | HRA 9021 |
UST-ld Nr. DE812136745
-----Original Message-----
From: si-list-bounce@xxxxxxxxxxxxx [mailto:si-list-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Carson Au
Sent: Thursday, July 07, 2016 11:47 PM
To: si-list@xxxxxxxxxxxxx
Subject: [SI-LIST] Pros and Cons of Through-hole / SMT DIMM Sockets
Hi experts,
I've always wondered about the availability of through-hole / press-fit and SMT
versions of DDR3 and DDR4 DIMM sockets
<http://www.molex.com/molex/products/family?key=ddr4_dimm_sockets&channel=products&chanName=family&pageTitle=Introduction&utm_source=dpb&utm_medium=lit&utm_campaign=general&WT.mc_id=A03253>
.
Are there any signal integrity tradeoffs here (I don't see any relevance here
at DDR4 signal rates and edges)? Why would someone consider through-hole over
SMT? Are there reflow or mechanical issues?
Regards,
Carson
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List forum is accessible at:
http://tech.groups.yahoo.com/group/si-list
List archives are viewable at:
//www.freelists.org/archives/si-list
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu
------------------------------------------------------------------
To unsubscribe from si-list:
si-list-request@xxxxxxxxxxxxx with 'unsubscribe' in the Subject field
or to administer your membership from a web page, go to:
//www.freelists.org/webpage/si-list
For help:
si-list-request@xxxxxxxxxxxxx with 'help' in the Subject field
List forum is accessible at:
http://tech.groups.yahoo.com/group/si-list
List archives are viewable at:
//www.freelists.org/archives/si-list
Old (prior to June 6, 2001) list archives are viewable at:
http://www.qsl.net/wb6tpu