[roc-chat] Re: Measure
- From: Sergei Sapozhkov <msergeim@xxxxxxx>
- To: "roc-chat@xxxxxxxxxxxxx" <roc-chat@xxxxxxxxxxxxx>
- Date: Fri, 18 Oct 2013 21:23:14 -0700
Thanks Carlo. This is the info I was looking for
Thank you
Sergei Sapozhkov
> On Oct 18, 2013, at 9:06 PM, Carlo Vaccari <airplaniac2002@xxxxxxxxx> wrote:
>
> I used a single 1/8" vent hole at the very base of the nosecone at Mach 1.65
> or so and it worked fine.
>
> What electronics are you using? Most modern ones (a properly programmed
> Raven, or the RRC3, or the Stratologger) are immune to weirdness in baro data.
>
>
>> On Sat, Oct 19, 2013 at 12:04 AM, Sergei Sapozhkov <msergeim@xxxxxxx> wrote:
>> I am working on my minimum diameter and calculation show about M1.6 I just
>> want to make sure my electronic will work correctly
>>
>> Thank you
>>
>> Sergei Sapozhkov
>>
>>> On Oct 18, 2013, at 8:52 PM, Carlo Vaccari <airplaniac2002@xxxxxxxxx> wrote:
>>>
>>> You can use a larger hole than necessary without problems, especially at
>>> the scale you're working with.
>>>
>>>
>>>> On Fri, Oct 18, 2013 at 11:51 PM, Sergei Sapozhkov <msergeim@xxxxxxx>
>>>> wrote:
>>>> This is my problem . I have only bits and I need to drill hole in avionics
>>>> bay for altimeter. Recommendation for 38mm tube I need to drill 0.032" and
>>>> I am not sure for drill to use
>>>>
>>>> Thank you
>>>>
>>>> Sergei Sapozhkov
>>>>
>>>>> On Oct 18, 2013, at 8:43 PM, David Smith <davew6dps@xxxxxxxxx> wrote:
>>>>>
>>>>> .032" is a standard size 67 drill. Do you have number size pin drills or
>>>>> a place to get one?
>>>>>
>>>>> Is the dimension that critical?
>>>>>
>>>>> David P Smith
>>>>> NAR 78668, L2
>>>>> Amateur Extra, W6DPS
>>>>>
>>>>>
>>>>>> On Fri, Oct 18, 2013 at 8:07 PM, Sergei Sapozhkov <msergeim@xxxxxxx>
>>>>>> wrote:
>>>>>> I think minimum I have is 1/16 and then 3/32. That would be a difficult
>>>>>> for me
>>>>>>
>>>>>> Thank you
>>>>>>
>>>>>> Sergei Sapozhkov
>>>>>>
>>>>>> > On Oct 18, 2013, at 8:02 PM, Michael Levin <sailmike@xxxxxxxxxxxxx>
>>>>>> > wrote:
>>>>>> >
>>>>>> > A 1/32" = 0.03125" hole. See what drill bits you have and run the
>>>>>> > fraction through a calculator.
>>>>>> >
>>>>>> > Mike
>>>>>> > Sent from my extremely cool iPhone
>>>>>> >
>>>>>> >> On Oct 18, 2013, at 19:44, Sergei Sapozhkov <msergeim@xxxxxxx> wrote:
>>>>>> >>
>>>>>> >> I need to make a hole 0.032" What bit I need to use. I am really bad
>>>>>> >> with inches
>>>>>> >>
>>>>>> >> Thank you
>>>>>> >>
>>>>>> >> Sergei Sapozhkov
>>>>>> >> --
>>>>>> >> ROC-Chat mailing list
>>>>>> >> roc-chat@xxxxxxxxxxxxx
>>>>>> >> //www.freelists.org/list/roc-chat
>>>>>> >
>>>>>> > --
>>>>>> > ROC-Chat mailing list
>>>>>> > roc-chat@xxxxxxxxxxxxx
>>>>>> > //www.freelists.org/list/roc-chat
>>>>>> >
>>>>>>
>>>>>> --
>>>>>> ROC-Chat mailing list
>>>>>> roc-chat@xxxxxxxxxxxxx
>>>>>> //www.freelists.org/list/roc-chat
>
Other related posts:
