The page for this Iron says reaches temp in 7 seconds. What are you finding
for the time it takes to get the join done from when you push the button to
release the iron from joint?
-----Original Message-----
From: raspberry-vi-bounce@xxxxxxxxxxxxx <raspberry-vi-bounce@xxxxxxxxxxxxx> On
Behalf Of Michael A Ray (Redacted sender "mike.ray" for DMARC)
Sent: Wednesday, March 3, 2021 6:00 PM
To: raspberry-vi@xxxxxxxxxxxxx
Subject: [raspberry-vi] Re: Instant heat battery soldering irons
Jean-Claude,
I have just updated the post at:
http://www.raspberryvi.org/posts/battery-iron-soldering.html
So that the link to RS Components here in the UK takes you right to the very
iron.
Sit down before you look at the price. And then the price of the charger, which
is sold separately.
Mike
On 03/03/2021 22:20, Jean-Claude Provost wrote:
Hi Mike,
I tried to find the iron on the site you mentioned but could not... Would
you have a direct link?
Also, do you know if they ship outside the UK?
Thanks,
Cheers,
Jean-Claude Provost
-----Original Message-----
From: raspberry-vi-bounce@xxxxxxxxxxxxx
<raspberry-vi-bounce@xxxxxxxxxxxxx> On Behalf Of Michael A Ray
(Redacted sender "mike.ray" for DMARC)
Sent: Wednesday, March 3, 2021 10:39 AM
To: raspberry-vi@xxxxxxxxxxxxx
Subject: [raspberry-vi] Re: Instant heat battery soldering irons
Today I got an RS own brand battery soldering iron.
It is billed on uk.rs-online.com as a 15 Watt iron.
It has a body which is about an inch square. It is light enough to hold like
a pen, and the button to apply power to the tip is light enough in touch that
you won't get finger ache after hours of use.
It was a VERY expensive iron, so not everybody will be able to afford it. But
after doing a lot of research online I came to the conclusion that this was
the iron with the fastest heating tip. And I really wanted to be able to get
back to soldering stuff into vero.
I have today soldered a 555 timer into some veroboard, and directly wired all
eight pins of a DPDT relay by winding some hook-up wire around each leg and
then soldering.
The joints feel every bit as good as those I would have made when I could see.
The tip heats so quickly I can guide it to where I want the joint while it is
cold, with a finger tip, take up the solder and then press the solder to the
other side of the joint and then press the button.
It remains to be seen how long a charge lasts. And how long a tip lasts.
I would not use this iron to solder stuff like PL259 coaxial plugs, not big
and powerful enough. For that I have a Weller gun.
On 03/03/2021 11:44, Ken Perry wrote:
Our engineer at APH has tried many of the battery power quick heat irons.
The reason I have not bought one is he said that most last a few
weeks and then they die. That or you have to keep replacing the tips
because they quickly burn out. I have yet to find one any better
than what he has told me about. So if you guys find any that last a
while and or don't cost you a lot in the long run. I am interested.
-----Original Message-----
From: raspberry-vi-bounce@xxxxxxxxxxxxx
<raspberry-vi-bounce@xxxxxxxxxxxxx>
On Behalf Of Tom Fowle
Sent: Wednesday, March 3, 2021 12:41 AM
To: raspberry-vi@xxxxxxxxxxxxx
Subject: [raspberry-vi] Re: Instant heat battery soldering irons
Mike,
I am not up to date on irons. However you'll find in the tech file
the "vinther fingertip iron or something like that. This uses a tip
intended for a battery iron to be used in tight spaces. The
controller for this gizmo monitors the resistance of the tip as it
heats and limits the tip current so as to approximately control temperature.
The tip is on a lightweight piece of zip cord and is controlled with
a footswitch.
Whether one could find this tip these days is of some doubt but the
ideas may inspire some research. I personally advise use of a fine
tipped temperature controlled iron as Bill Gerrey reccommends. Using
a light weight temp controlled iron with a handy sturdy stand to bung
it into between joints is, with practice, a manageable method. I have
never seen a light weight instant hot iron except the Vinther as
above. Lots of current pumped in fast means big wires.
Or so run my beliefs from years back.
Tom Fowle
===========================================================
The raspberry-vi mailing list
Archives: //www.freelists.org/archives/raspberry-vi
Administrative contact: <mike.ray@xxxxxxxxxxxxxx>
-----------------------------------------------------------
Raspberry Pi and the Raspberry Pi logo are trademarks of the
Raspberry Pi Foundation.
This list is not affiliated to the Raspberry Pi Foundation and the
views and attitudes expressed by the subscribers to this list do not
reflect those of the Foundation.
Mike Ray, list creator, January 2013
===========================================================
The raspberry-vi mailing list
Archives: //www.freelists.org/archives/raspberry-vi
Administrative contact: <mike.ray@xxxxxxxxxxxxxx>
-----------------------------------------------------------
Raspberry Pi and the Raspberry Pi logo are trademarks of the Raspberry Pi
Foundation.
This list is not affiliated to the Raspberry Pi Foundation and the views and
attitudes expressed by the subscribers to this list do not reflect those of
the Foundation.
Mike Ray, list creator, January 2013
--
Michael A. Ray
Analyst/Programmer
Witley, Surrey, South-east UK
"Perfection is achieved, not when there is nothing more to add, but
when there is nothing left to take away." -- A. de Saint-Exupery
https://cromarty.github.io/
http://eyesfreelinux.ninja/
http://www.raspberryvi.org/
===========================================================
The raspberry-vi mailing list
Archives: //www.freelists.org/archives/raspberry-vi
Administrative contact: <mike.ray@xxxxxxxxxxxxxx>
-----------------------------------------------------------
Raspberry Pi and the Raspberry Pi logo are trademarks of the Raspberry Pi
Foundation.
This list is not affiliated to the Raspberry Pi Foundation and the views and
attitudes expressed by the subscribers to this list do not reflect those of
the Foundation.
Mike Ray, list creator, January 2013
===========================================================
The raspberry-vi mailing list
Archives: //www.freelists.org/archives/raspberry-vi
Administrative contact: <mike.ray@xxxxxxxxxxxxxx>
-----------------------------------------------------------
Raspberry Pi and the Raspberry Pi logo are trademarks of the Raspberry Pi
Foundation.
This list is not affiliated to the Raspberry Pi Foundation and the views and
attitudes expressed by the subscribers to this list do not reflect those of
the Foundation.
Mike Ray, list creator, January 2013
===========================================================
The raspberry-vi mailing list
Archives: //www.freelists.org/archives/raspberry-vi
Administrative contact: <mike.ray@xxxxxxxxxxxxxx>
-----------------------------------------------------------
Raspberry Pi and the Raspberry Pi logo are trademarks of the Raspberry Pi
Foundation.
This list is not affiliated to the Raspberry Pi Foundation and the views and
attitudes expressed by the subscribers to this list do not reflect those of
the Foundation.
Mike Ray, list creator, January 2013
