Does any one has DI700BD document, if yes kindly e-mail me on my e-mail address, Rgds, Imran Butt. On 9/12/07, Landry, Scott <scott.landry@xxxxxxxxxxxxxxxx> wrote: > > Imran, > > > Are you using direct connect, AB1785KE or AB-KF2 ? > > As far as I know the direct connect method is not supported. > > AB1785KE is: > > A2,A4,A6,A8 --- B8 --- C1,C4,C5 closed (all others open) > > AB-KF2 is: > > A2,A4,A6,A8 --- B8 --- C1 and C5 closed (all others open) > > > Please refer to DI700BD FDSI Driver Allen Bradley DH+ Protocol > > > Regards, > > > Scott L. Landry > Invensys Process Systems/Foxboro > Gulf Coast Region USA > > > > -----Original Message----- > From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] > On= > Behalf Of Imran Waheed Butt > Sent: Wednesday, September 12, 2007 3:39 AM > To: foxboro@xxxxxxxxxxxxx > Subject: Re: [foxboro] Communication problem b/w FBM231 & AB PLC > > Sorry that is DI15 > On 9/12/07, Imran Waheed Butt <butt.imran@xxxxxxxxx> wrote: > > > > Dear Kevin, > > > > Sorry there there was not MG30 that is COMM15 we were using now that is > > replaced by FBM231. > > > > Thanks and Regards, > > Imran > > > > > > On 9/12/07, Kevin Fitzgerrell <fitzgerrell@xxxxxxxxx> wrote: > > > > > > Imran, > > > > > > How are you using an MG30 to communicate with an AB PLC? Are you > > > using a Prosoft card? > > > > > > Regards, > > > > > > Kevin FitzGerrell > > > > > > On 9/12/07, Imran Waheed Butt <butt.imran@xxxxxxxxx> wrote: > > > > Dear All, > > > > Our customer is upgrading the I/A version form V4.3 Unix to V8.2 on > X= > P > > > and > > > > previous system has CP30FT communicating with 100 series FBMs and > FBC= > s > > > and > > > > quantity 3 MG30 gateways communicating with Allen Bradley PLC > through= > > > > CAM or > > > > Modem which is provided by Allen Bradley. > > > > > > > > The CP30FT is upgraded to FCP270FT and 100 series FBM and FBC are > > > remain > > > > same. > > > > > > > > The 3 no. MG30 are replaced by and other FCP270FT with FBM231 (FT). > > > > > > > > I am at the commissioning/installation of the system and facing > > > following > > > > problems, > > > > > > > > 1. FBM231 is not communicating with AB PLC through CAM or Modem > as= > > > > we > > > > translate the same DIP switch setting which is on the P0970VN > (MG30= > > > > > configuration selection switch) to the FBM231 TA, the switch > > > settings are > > > > as, > > > > MG30>>> SW1-1,2,3,4,7,8 & SW2-1,3,4,6,8 are closed and > > > > remaining are open > > > > we translate them form documents B0193RL-Rev H page 49-50 and form > > > > B0700AH Rev E page 62-63 and translated switch setting are as, > > > > FBM231 TA>>> A-2,4,6,8 & B-4,8 & C-1 are close and > > > > remaining are open. > > > > But it is not communicating with PLC. > > > > 2. The cable part number which is connecting PLC to Gateway is > > > > P0970WY-C and we are using the same cable. > > > > 3. Previously AIN, AOUT, CIN and COUT blocks are in the database > of= > > > > > MG30 which communicate with PLC, and now these blocks we can't use > > > with > > > > FBM231 to communicate with PLC so, we create RIN, ROUT, BIN and > BOU= > T > > > blocks > > > > and connect the out put of these blocks to the input of AIN and > CIN= > > > > and > > > > output of COUT and AOUT to input of BOUT and ROUT. > > > > Now problem is that the previous addressing of PNT parameter of > CIN= > > > > is > > > > and COUT are like 4.12:0 and 16.15:0 and for AIN and AOUT have > like= > > > > > 126:0 at their PNT parameter. Kindly guide me how to translate the > > > above > > > > format to PNT parameter to the format of BIN,BOUT, RIN and ROUT. > > > > We copy the same PNT no. to the PNT of BIN, BOUT, RIN, ROUT's PNT > > > but > > > > when loaded to FCP it gives error W65. > > > > > > > > Kindly all the experts provide me solution of above issues. > > > > > > > > > > > > > > > > Thanks and Best Regards, > > > > > > > > Imran Butt, > > > > > > > > System Engineer, > > > > > > > > Manstock. > > > > > > > > > > > > > > > > > > _______________________________________________________________________= > > > > This mailing list is neither sponsored nor endorsed by Invensys > Process= > > > > Systems (formerly The Foxboro Company). Use the info you obtain here > at= > > > > your own risks. Read > http://www.thecassandraproject.org/disclaimer.html= > > > > > > > foxboro mailing list: > //www.freelists.org/list/foxboro= > > > > to subscribe: mailto: > foxboro-request@xxxxxxxxxxxxx?subject=3Dj= > oin > > > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx > ?subject=3Dlea= > ve > > > > > > > > > > > > -- > > Thanks and Best Regards, > > Imran Butt > > System Engineer > > Manstock Engineering Company (Pvt.) Ltd. > > 39-42 Farid Chambers, Abdullah Haroon Road > > Karachi =E2=80=93 74400, Pakistan > > Cell: +92-321-2102686 > > Home: +92-21-4590568 > > Office: +92-21-5678952, 5678953, 5673145 > > FAX: +92-21-5682576 > > E-mail: butt.imran@xxxxxxxxx > > URL: http://www.manstock-engg.com > > > > > -- = > > Thanks and Best Regards, > Imran Butt > System Engineer > Manstock Engineering Company (Pvt.) Ltd. > 39-42 Farid Chambers, Abdullah Haroon Road > Karachi =E2=80=93 74400, Pakistan > Cell: +92-321-2102686 > Home: +92-21-4590568 > Office: +92-21-5678952, 5678953, 5673145 > FAX: +92-21-5682576 > E-mail: butt.imran@xxxxxxxxx > URL: http://www.manstock-engg.com > > = > > = > > _______________________________________________________________________ > This mailing list is neither sponsored nor endorsed by Invensys Process > Systems (formerly The Foxboro Company). Use the info you obtain here at > your own risks. Read http://www.thecassandraproject.org/disclaimer.html > = > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=3Djoin > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=3Dleave > = > > > > Confidentiality Notice: > This e-mail and any associated files are intended solely for the > individual= > or entity to whom they are addressed. Please do not copy it or use it for > = > any purposes, or disclose its contents to any other person. Further, this > e= > -mail and any associated files may be confidential and further may be > legal= > ly privileged. This email is from the Invensys Process Systems business > uni= > t of Invensys plc which is a company registered in England and Wales with > i= > ts registered office at Portland House, Bressenden Place, London, SW1E 5BF > = > (Registered number 166023). For a list of European legal entities within > t= > he Invensys Process Systems business group, please click here > http://www.in= > vensys.com/legal/default.asp?top_nav_id=3D77&nav_id=3D80&prev_id=3D77. > > If you have received this e-mail in error, you are on notice of its > status.= > Please notify us immediately by reply e-mail and then delete this message > = > from your system. Thank you for your co-operation. You may contact our > Help= > desk on +44 (0)20 7821 3859 / 2105 or email inet.hqhelpdesk@xxxxxxxxxxxxx > T= > his e-mail and any attachments thereto may be subject to the terms of any > a= > greements between Invensys (and/or its subsidiaries and affiliates) and > the= > recipient (and/or its subsidiaries and affiliates). > > > > > _______________________________________________________________________ > This mailing list is neither sponsored nor endorsed by Invensys Process > Systems (formerly The Foxboro Company). Use the info you obtain here at > your own risks. Read http://www.thecassandraproject.org/disclaimer.html > > foxboro mailing list: //www.freelists.org/list/foxboro > to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join > to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave > > _______________________________________________________________________ This mailing list is neither sponsored nor endorsed by Invensys Process Systems (formerly The Foxboro Company). Use the info you obtain here at your own risks. Read http://www.thecassandraproject.org/disclaimer.html foxboro mailing list: //www.freelists.org/list/foxboro to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave