[ExchangeList] Re: Problem with relaying for authenticated users
- From: <ChongJa@xxxxxxxxxxxxxxxx>
- To: <exchangelist@xxxxxxxxxxxxx>
- Date: Wed, 9 Aug 2006 18:30:51 -0400
Can you post the exact NDR message?
James Chong
Exchange | Administrator
MCSE | M+, S+, MCTS, Security+
Cell: 703| 206|7548 (work)
Cell: 703| 863|1483
chongja@xxxxxxxxxxxxxxxx
________________________________
From: exchangelist-bounce@xxxxxxxxxxxxx on behalf of Evan Mann
Sent: Wed 8/9/2006 5:40 PM
To: exchangelist@xxxxxxxxxxxxx
Subject: [ExchangeList] RE: [ExchangeList] Re: Problem with relaying for
authenticated users
Ran EXBPA, nothing wrong in the VS reported (aside from my # of
connections/messages thresholds, but that's unrelated)
Access Tab/Auth - Anon Checked, Basic Checked (require TLS not checked),
Integrated Checked
Access Tab/Auth/Users subtab - Authenticated Users set to submit permission
Access Tab/Relay - Only the list below checked (list empty), Allow all
computers which successfully auth to relay, regardless of the list above is
checked
These are all default settings based on what I've read and remember.
The Access/Auth/Users subtab is interesting. There is an option for "relay
permission" which is not checked for authenticated users. I checked it but
still no go. Do I need to restart the SMTP VS for this change to take effect?
Is this change required? Everything I read about relaying deals with the
Access/Relay tab only, and not the Auth tab.
________________________________
From: exchangelist-bounce@xxxxxxxxxxxxx
[mailto:exchangelist-bounce@xxxxxxxxxxxxx] On Behalf Of ChongJa@xxxxxxxxxxxxxxxx
Sent: Wednesday, August 09, 2006 5:21 PM
To: exchangelist@xxxxxxxxxxxxx
Subject: [ExchangeList] Re: Problem with relaying for authenticated users
Go ahead and run EXBPA, it usually reports issues with SMTP VS config setups.
Also what settings are configured in your Access tab of your SMTP VS?
________________________________
From: exchangelist-bounce@xxxxxxxxxxxxx
[mailto:exchangelist-bounce@xxxxxxxxxxxxx] On Behalf Of Evan Mann
Sent: Wednesday, August 09, 2006 3:24 PM
To: exchangelist@xxxxxxxxxxxxx
Subject: [ExchangeList] RE: [ExchangeList] Re: Problem with relaying for
authenticated users
Setup has been in place 2 years now or so. I only get this when I sent to
non-hosted e-mail addresses. I can send to any email address hosted on the
exchange server fine. You don't even need the check box for outbound mail
server requires authentication to send to addresses hosted on the server.
I'm almost positive this worked in the past, possibly before SP2.. hmmm
________________________________
From: exchangelist-bounce@xxxxxxxxxxxxx
[mailto:exchangelist-bounce@xxxxxxxxxxxxx] On Behalf Of ChongJa@xxxxxxxxxxxxxxxx
Sent: Wednesday, August 09, 2006 3:19 PM
To: exchangelist@xxxxxxxxxxxxx
Subject: [ExchangeList] Re: Problem with relaying for authenticated users
Is this a new setup? You get this when you send to any address? Run Exchange
Best Practice analyzer, possible there may be some misconfiguration within your
SMTP VS.
________________________________
From: exchangelist-bounce@xxxxxxxxxxxxx
[mailto:exchangelist-bounce@xxxxxxxxxxxxx] On Behalf Of Evan Mann
Sent: Wednesday, August 09, 2006 3:02 PM
To: exchangelist@xxxxxxxxxxxxx
Subject: [ExchangeList] Problem with relaying for authenticated users
Exchange 2003 SP2.
Users get an error 550, recipient address rejected. no such user if they try
to relay through the mail server. I'm doing tests using Outlook 2003 setup for
IMAP. I enabled the advanced settings to require authentication on the
outbound mail server., and the default relaying options are enabled which
should allow this to work. I double-checked.
I must be missing something obvious here?
Other related posts:
