[duxuser] Re: VersaPoint Duo problem
- From: "Mark Mercer" <markm@xxxxxxxxxxxx>
- To: <duxuser@xxxxxxxxxxxxx>
- Date: Mon, 22 Nov 2004 11:21:50 -0500
Hi Rosy,
A typo in the instructions, here is the corrected sentence:
There is a piece of metal that holds the paper down and the cutout is just
to the right of the piece of metal.
Best Regards,
Mark
----- Original Message -----
From: "Mark Mercer" <markm@xxxxxxxxxxxx>
To: <duxuser@xxxxxxxxxxxxx>
Sent: Monday, November 22, 2004 11:15 AM
Subject: [duxuser] Re: VersaPoint Duo problem
> Hi Rosy,
>
> It sounds like you have paper dust on the sensor. Take a Q-Tip with a
> little rubbing alcohol (almost dry, no dripping) and wipe off the sensor.
> The center on the sensor cutout in the case is located approximately
2-3/4"
> from the left side plate under the lid. There is a piece of metal that
> holds the paper down and the cutout is just to the right of the cutout.
>
> The second problem sounds like you changed from 11" wide paper to 8.5"
wide
> paper. The embosser is set to default to 40 characters wide, try the
> following embosser settings if you are using narrow paper:
>
> Press the OL key
> Enter 0*1#
> Enter 15*1#
> Enter 14*30#
> Enter 1*1#
>
> Make sure DBT is set for the proper page size:
> Open you document.
> Press CTRL-F11
> Make sure the Brailler Device: is set to "Freedom Scientific VersaPoint
> Duo".
> Make sure the Form: field is set to Narrow Width, 11 inch Long, Braille
> Paper
> Set the Characters per line: to 30
> Set the Lines per page: to 25
> Tab to OK and press enter.
> Press ctrl-e to enter File: Emboss
> Tab to OK and press enter to emboss the document.
>
> I hope this helps.
>
> Best Regards,
> Mark
>
>
>
> ----- Original Message -----
> From: "Rosy Goodrich" <rosegood@xxxxxxxxxxxxx>
> To: <duxuser@xxxxxxxxxxxxx>
> Sent: Saturday, November 20, 2004 11:36 PM
> Subject: [duxuser] Re: versapoint manual
>
>
> > George,
> >
> > Thanks for your post; I'm simply frustrated because it's supposed to
> > work. When things don't work, I'm lost; when they do, I'm happy. I
> > thought it was working fine, but I changed paper, and did nothing else,
> > and now it won't work right. Not good!
> >
> >
> >
> > * * *
> > * This message is via list duxuser at freelists.org.
> > * To unsubscribe, send a blank message with
> > * unsubscribe
> > * as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also
> > * subscribe, unsubscribe, and set vacation mode and other subscription
> > * options by visiting //www.freelists.org. The list archive
> > * is also located there.
> > * Duxbury Systems' web site is http://www.duxburysystems.com
> > * * *
>
> * * *
> * This message is via list duxuser at freelists.org.
> * To unsubscribe, send a blank message with
> * unsubscribe
> * as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also
> * subscribe, unsubscribe, and set vacation mode and other subscription
> * options by visiting //www.freelists.org. The list archive
> * is also located there.
> * Duxbury Systems' web site is http://www.duxburysystems.com
> * * *
* * *
* This message is via list duxuser at freelists.org.
* To unsubscribe, send a blank message with
* unsubscribe
* as the subject to <duxuser-request@xxxxxxxxxxxxx>. You may also
* subscribe, unsubscribe, and set vacation mode and other subscription
* options by visiting //www.freelists.org. The list archive
* is also located there.
* Duxbury Systems' web site is http://www.duxburysystems.com
* * *
Other related posts:
