Oh,
I wasn't suggesting hacking anything or re-inventing ground. Only
simple thoughts like a wire at an unconnected ground screw on a power
conditioner for example. Sorry for any confusion...
On 5/31/17, DJX <megamansuperior@xxxxxxxxxxx> wrote:
Make sure you eliminate the sound, but please please please! *NEVER* get ridPLEASE READ THIS FOOTER AT LEAST ONCE!
of ground, or use something as ground that shouldn't be. That could damage
your equipment before you even turn it on or cause other problems like EMI.
Becareful with ground lifting, which just gets rid of the ground. If you
know what you're doing, or are working with somebody who does, you should be
able to get great results without resorting to crazy hacks that can only
damage equipment or kill you!
But it all does start with a good, well thought out wiring scheme. Also,
consider all the equipment you have in the chain, and I mean all of it, from
the smallest to the greatest.
Regards, DJX
-----Original Message-----
From: ddots-l-bounce@xxxxxxxxxxxxx [mailto:ddots-l-bounce@xxxxxxxxxxxxx] On
Behalf Of floyd white
Sent: Tuesday, May 30, 2017 10:47 PM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: Power distribution on a budget
Yup,
Well, on a budget is going to be tough.
When I first built my studio up, 60 cycle drove me nuts.
My advice is experiment.
For example,
* try to avoid running audio cables along side ac power in parallel.
* Stay balance audio everywhere if you can afford it.
* Experiment with ground wires from power conditioners or outlet strips to
real ground like water pipes etc. You'll need to do this with headphones on
and with nothing except white noise in them.
This approach ought to keep you busy for like weeks.
It's all about eliminating ground loops.
And after all that, you might be lucky enough to reduce your noise maby 20
to 30 percent.
Unless you are willing to dig in with a bunch of money and as DJX said an
expert, you may have to work around noise as well as incorporate a good
noise reduction plug-in to help.
There are a number of good ones like Cedar, Isotope etc.
On 5/30/17, DJX <megamansuperior@xxxxxxxxxxx> wrote:
Bettef than wasting time reading books that will mainly focus on whatPLEASE READ THIS FOOTER AT LEAST ONCE!
you already stated you can't change, the building's electrical, you
would be better off consulting with someone who is experienced in
studio set up, and can help you work on your particular setup. V
Regards, DJX
________________________________
From: ddots-l-bounce@xxxxxxxxxxxxx <ddots-l-bounce@xxxxxxxxxxxxx> on
behalf of Fran franks <fm.guitarlady@xxxxxxxxx>
Sent: Tuesday, May 30, 2017 4:55:26 PM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Power distribution on a budget
Hello all,
Can any of you recommend good publications I can read on the subject
of power distribution in the recording studio?
I'm not formally trained as an engineer and often find myself
perplexed and frustrated in my efforts to eliminate stray fields that
cause the dreaded 60Hz hum. Unfortunately though, I am not in the
position to change the building architecture, including redesigning the
house electrical system.
So, I'm hoping there is an affordable way to isolate the room I have
set up as a studio.
Warm regards,
Fran Franks
PLEASE READ THIS FOOTER AT LEAST ONCE!
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=subscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode, click on the
immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject q or send a message, to
ddots-l-request@xxxxxxxxxxxxx and in the Subject line type faq
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=subscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode, click on the immediately
following link:
ddots-l-request@xxxxxxxxxxxxx?subject q or send a message, to
ddots-l-request@xxxxxxxxxxxxx and in the Subject line type faq
