Xavier,
I have sonar, the focus right, and the DAT machine. I do not have a separate
master clock. With this in mind, what is the correct order? There is no word
clock involved here.
Sent from my iPhone
On May 26, 2017, at 6:27 PM, DJX <megamansuperior@xxxxxxxxxxx> wrote:
Kevin, check clock sources, and make sure the 2 units are in syncn. Remember
with SPDIF sometimes order is important. Since the audio source is usually
the one that hold master clock, turn it on first so it starts sending out a
clock signal, then turn on the saffire a few seconds later, so that it has a
clock to sync to. Be sure that it is in fact using an external clock source
and not internal.
Regards, DJX
From: ddots-l-bounce@xxxxxxxxxxxxx <ddots-l-bounce@xxxxxxxxxxxxx> on behalf
of Kevin Gibbs <kevjazz@xxxxxx>
Sent: Friday, May 26, 2017 7:05:28 PM
To: ddots-l@xxxxxxxxxxxxx
Subject: [ddots-l] Re: Help recording content from old DAT Machine into Sonar
8.5
Floyd,
Just got an email from another list recommending that I check my sample rate
on the DAT. I suspect that will solve the problem. Not home now. Will check
later.
Sent from my iPhone
On May 26, 2017, at 5:41 PM, floyd white <cavernrecording@xxxxxxxxx> wrote:PLEASE READ THIS FOOTER AT LEAST ONCE!
Hi Kevin,
I'm not familiar with your interface but do you have any way of using
analog outs from your DAT into your interface?
On 5/26/17, Kevin Gibbs <kevjazz@xxxxxx> wrote:PLEASE READ THIS FOOTER AT LEAST ONCE!
Dear all,
I really need help on this one. I own a DAT Machine which is connected via
SPDIF to my focus right 18i20. Yesterday, and for a couple days before
then, I was transferring The contents of old DAT tapes into sonar without
any issues.
Today, when I fired up my system to continue making these transfers, I was
on able to record anything at all. I also tried this in Reaper. I should
note that I opened and armed Reaper first, before opening sonar, because I
wanted to save my files as FLAC To save space.
When I was on able to record in reaper, I opened sonar and discovered that
I
couldn't get any content there, either.
For the sake of this discussion, I will stay focused in sonar. Here are
the
things I have done:
I made sure that the track I wanted was assigned to the SPDIF input and the
master output.
2. Made sure that the track was armed and that input monitoring was
enabled.
3. For the record, I had done the same things in reaper when I tried that
as well.
I know that the tapes have content because I monitored through my
headphones
using the headphone jack on the DAT Machine.
I also have enough vision to see the display on the DAT Machine and saw the
VU meters registering as the content played.
While this should not have been necessary I also reached back to make sure
that my cables were properly seated. These cables are almost brand-new in
as much as they have almost never been used.
Also made sure that SPDIF what is enabled in my focus right control panel.
I
don't need accessibility I have enough vision to use a mouse when
necessary.
Powered down and rebooted computer twice.
WTF?
Any help greatly appreciated from reaper or sonar or Samplitude users.
Haven't gone to Samplitude yet because I don't think the choice of DAW has
anything to do with this.
Thanks for any help,
Kevin
Sent from my iPhone
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=unsubscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=faq or
send a message, to
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
faq
To leave the list, click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject=subscribe
If this link doesn't work then send a message to:
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
unsubscribe
For other list commands such as vacation mode,
click on the immediately following link:
ddots-l-request@xxxxxxxxxxxxx?subject?q or
send a message, to
ddots-l-request@xxxxxxxxxxxxx
and in the Subject line type
faq