[TechAssist] Re: RCA VCR VR528/VG4039(GE VERSION) INTERMITTANT POWER

thank you paul, i will ck into it further,
gary
Gary Chambers
Chambers T V
Bradenton,Florida
Since 1982
----- Original Message -----
From: "C&W Electronics" <c_w_electronics@xxxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Wednesday, October 31, 2001 8:24 PM
Subject: [TechAssist] Re: RCA VCR VR528/VG4039(GE VERSION) INTERMITTANT
POWER


>
> Don't know Gary, this was listed in my vcr data file under VG4025, but the
> symptoms were what you described, so I thought that may be the same. It
was
> listed as the precision feed back for the power supply. I don't have any
pwr
> supply symptoms under the models that you listed. This is probably a
> different chassis. But, it was worth a shot.
> Good hunting.
> Paul W
> C&W Electronics
>
>
> From: "GJCHAMBERS" <gjchambers@xxxxxxxxxxx>
> Reply-To: techassist@xxxxxxxxxxxxx
> To: <techassist@xxxxxxxxxxxxx>
> Subject: [TechAssist] Re: RCA VCR VR528/VG4039(GE VERSION) INTERMITTANT
> POWER
> Date: Wed, 31 Oct 2001 19:04:29 -0400
>
>
> I replaced the voltage comparator ic ip003 but dont see an ic3.
> is this the same one? has 8 pins.
> thanks ,
> gary
> Gary Chambers
> Chambers T V
> Bradenton,Florida
> Since 1982
> ----- Original Message -----
> From: "C&W Electronics" <c_w_electronics@xxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Wednesday, October 31, 2001 7:51 PM
> Subject: [TechAssist] Re: RCA VCR VR528/VG4039(GE VERSION) INTERMITTANT
> POWER
>
>
>  >
>  > Gary, check for defective IC3(KA431Z) in secondary of p/s. RCA#212572.
I
>  > have this listed as defective like the C09 bad on other sets. The set
> only
>  > blinks.
>  > Paul W
>  > C&W Electronics
>  >
>  >
>  > From: "GJCHAMBERS" <gjchambers@xxxxxxxxxxx>
>  > Reply-To: techassist@xxxxxxxxxxxxx
>  > To: <techassist@xxxxxxxxxxxxx>
>  > Subject: [TechAssist] RCA VCR VR528/VG4039(GE VERSION) INTERMITTANT
POWER
>  > Date: Wed, 31 Oct 2001 17:48:06 -0400
>  >
>  > This vcr had diodes dpo26 and dp027 shorted,after replacing them vcr
now
>  > blinks on and off about once a second.the display blinks at this rate
as
>  > well.
>  > i replaced cp007,cp008, ipoo1,ip003.
>  > also ck'ed the resistors on primary side of smps transformer and all ck
> ok.
>  > all voltages on secondary pulse up and down as well.
>  > acts sorta like the ones that used that 22 uf bipolar cap in primary.
>  > sometimes will stay on,untill you push a button, then starts cycling
> again.
>  > any ideas?
>  > thanks,
>  > gary
>  > Gary Chambers
>  > Chambers T V
>  > Bradenton,Florida
>  > Since 1982
>  >
>  >
>  > Help make your TechAssist online repair tips
>  > database better!  Submit your fixes here:
>  > http://www.circuitwork.com/techassist/tip/#tips
>  > To unsubscribe write to:
>  > techassist-request@xxxxxxxxxxxxx
>  > with  unsubscribe  in the subject line.
>  >
>  >
>  > _________________________________________________________________
>  > Get your FREE download of MSN Explorer at
> http://explorer.msn.com/intl.asp
>  >
>  > Help make your TechAssist online repair tips
>  > database better!  Submit your fixes here:
>  > http://www.circuitwork.com/techassist/tip/#tips
>  > To unsubscribe write to:
>  > techassist-request@xxxxxxxxxxxxx
>  > with  unsubscribe  in the subject line.
>
> Help make your TechAssist online repair tips
> database better!  Submit your fixes here:
> http://www.circuitwork.com/techassist/tip/#tips
> To unsubscribe write to:
> techassist-request@xxxxxxxxxxxxx
> with  unsubscribe  in the subject line.
>
>
> _________________________________________________________________
> Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp
>
> Help make your TechAssist online repair tips
> database better!  Submit your fixes here:
> http://www.circuitwork.com/techassist/tip/#tips
> To unsubscribe write to:
> techassist-request@xxxxxxxxxxxxx
> with  unsubscribe  in the subject line.

Help make your TechAssist online repair tips 
database better!  Submit your fixes here: 
http://www.circuitwork.com/techassist/tip/#tips
To unsubscribe write to:
techassist-request@xxxxxxxxxxxxx 
with  unsubscribe  in the subject line.

Other related posts: