I spent quite a while repairing a CTC169 PTV chassis once. The Vertically mounted Black Stretch Module(and main PCB area) looked like it had had something spilled there. There was mouse #2 everywhere also. I assumed it was mouse #1 that was the 'spillage'. The Black Stretch Module repaired the set(intermittent loss of Luminance/Horizontal Sync) Peggs At 04:00 PM 7/21/02 -0400, you wrote: > >What an original problem to find in a set. Was it a grey one or a brown or >white mouse? Is that mouse not house trained? I would not like a non house >trained mouse living in my living quarters! At least we can laugh about our >misshappenings or I hope so. >Have a good time and much profit. >Wilf Blakey >Blakey TV,Kirkland Lake,Ont >wblakey@xxxxxxxxxxxxxxxx > >----- Original Message ----- >From: "Gary McCartney" <number63@xxxxxxxxxxxxx> >To: <techassist@xxxxxxxxxxxxx> >Sent: July 20, 2002 6:34 PM >Subject: [TechAssist] RCA Chipper Checker, first time user, help please > > >> >> I have my new Chipper Checker connected to a CTC178L projection set. The >> set is dead because some mouses pee'd on the chassis (I mentioned this >> set a few months ago in case anyone remembers, but I only work on it >> when I'm caught up with customers items- it belongs to my buddy who is >> very patient). >> >> I installed the new eeprom and microprocessor kit before I got the >> Chipper Checker. >> Now with the Chipper Checker connected, I get error code 136, TVB (tone/ >> volume/ balance) which means U1503 is not communicating with the >> micrprocessor. Does this mean that U1503 or associated circuit is bad? >> I do have U1600 removed from the circuit (stereo decoder IC) so why >> doesn't Chipper Checker come up with error code 128 (no communication >> from U1600) ? >> How accurate is this Chipper Checker at determining faults? >> >> >> The basic problem with the set is that when remote power button is >> pressed, I get 3 chirps, then nothing. During these chirps, I get 120 V >> pulses B+ on the main 135V line, and I get a nice looking horizontal >> output waveform on the HOT collector. I have the flyback lead to the HV >> splitter disconnected. I removed U1600 because of corrosion on the pins. >> Replaced micro and eeprom because pins were corroded and thought that >> could be the problem with set not starting. I also have CRT boards >> unplugged from the tubes. >> >> >> Thanks for any help. >> -- >> >> >> >> Gary McCartney >> >> McCartney Electronics >> 7134 Fife Rd, RR 7 >> Guelph Ontario Canada N1H 6J4 >> Fax: (519)821-1530 >> email: number63 (at) inetsonic.com >> ------------------------------------------ >> To REMOVE your email address, click here: >> http://www.tech-assist.org/unsubb.html >> To CHANGE your email address, click here: >> http://www.tech-assist.org/change.html >> ------------------------------------------ >> ***NEW*** Tips Added Instantly!!!*** >> Submit Repair Tips here: >> http://www.tech-assist.org/secure/tip/ >> > >------------------------------------------ >To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html >To CHANGE your email address, click here: > http://www.tech-assist.org/change.html >------------------------------------------ >***NEW*** Tips Added Instantly!!!*** >Submit Repair Tips here: >http://www.tech-assist.org/secure/tip/ > Peggs' Electronics 1519 West 2nd Street Owensboro,KY 42301 ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.tech-assist.org/change.html ------------------------------------------ ***NEW*** Tips Added Instantly!!!*** Submit Repair Tips here: http://www.tech-assist.org/secure/tip/