I'll be sure to check this one, Thanks. Jim Myers jr.myers@xxxxxxxxxxx ----- Original Message ----- From: "D. Willoughby" <the_tv_guy@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Friday, November 02, 2001 10:28 AM Subject: [TechAssist] Re: RCA CTC157 chassis,video and audio mute intermittent > > Hi Jim! I just got done with one of these yesterday! Mine came in with no > vid, int sound. It had the weirdest fix! > Change the 220u cap on the back edge of the board next to the vert. > outp. It had shorted. Read ok with esr. > Hope this helps! > > Dave > The TV Guy > Billings, MT 59101 > 406-252-5649 > > ----- Original Message ----- > From: "TechAssist Admin." <techassist@xxxxxxxxxxxxxxxxxxxx> > To: <techassist@xxxxxxxxxxxxx> > Sent: Friday, November 02, 2001 4:11 AM > Subject: [TechAssist] Re: RCA CTC157 chassis,video and audio mute > intermittent > > > > > > (Jim, please do not cross post). Pulsing on/off problems > > could be the yoke. I'd check the traces all around the > > buffer (Q2901) because this definitely sounds like a problem > > with Q2901, particularly between the B-E. May also be Q2706, > > U3100, Q3107, C3319, Q3102, Q4401, T4301 & L4001. > > -Clint > > > > God Bless Us All > > Clint Hamilton, Owner > > http://OrpheusComputing.com > > sales@xxxxxxxxxxxxxxxxxxxx > > Fax: 209-882-9602 > > TechAssist Administration > > http://tech-assist.org > > techassist@xxxxxxxxxxxxx > > 4orpheus@xxxxxxxxxxxxx (alternates) > > orpheuscomputing@xxxxxxxxx > > pchardware@xxxxxxxxxxxx > > (PLEASE include previous correspondence > > if replying to this email!!) > > > > ----- Original Message ----- > > From: "Jim Myers" <jr.myers@xxxxxxxxxxx> > > To: <techassist@xxxxxxxxxxxxx> > > Cc: <tv-repair@xxxxxxxxxxxxxxx> > > Sent: Thursday, November 01, 2001 2:34 PM > > Subject: [TechAssist] RCA CTC157 chassis,video and audio mute > > intermittent > > > > > > RCA CTC157 chassis,video and audio mute intermittent > > > > Replaced Q2901 but no change, problem starts after about a > > ten minute warm up, then it is just on and off at random. HV, > > filaments, vertical, etc all ok as well as OSD, just goes to > > a blank screen and no sound. > > > > Has anyone seen this? Thanks. > > > > Jim Myers > > jr.myers@xxxxxxxxxxx > > > > Help make your TechAssist online repair tips > > database better! Submit your fixes here: > > http://www.circuitwork.com/techassist/tip/#tips > > To unsubscribe write to: > > techassist-request@xxxxxxxxxxxxx > > with unsubscribe in the subject line. > > > > > > > > Help make your TechAssist online repair tips > > database better! Submit your fixes here: > > http://www.circuitwork.com/techassist/tip/#tips > > To unsubscribe write to: > > techassist-request@xxxxxxxxxxxxx > > with unsubscribe in the subject line. > > > Help make your TechAssist online repair tips > database better! Submit your fixes here: > http://www.circuitwork.com/techassist/tip/#tips > To unsubscribe write to: > techassist-request@xxxxxxxxxxxxx > with unsubscribe in the subject line. Help make your TechAssist online repair tips database better! Submit your fixes here: http://www.circuitwork.com/techassist/tip/#tips To unsubscribe write to: techassist-request@xxxxxxxxxxxxx with unsubscribe in the subject line.