I use a 1 ohm resistor Peggs At 11:09 PM 12/12/02 -0500, David Lessard wrote: > >Jeff, > >Is this the PS diode feeding LA7838. I replaced (burnt out) resistor feeding >this diode, it was burnt beyond recognition so I replaced it with a 10 ohm - >1/2W, any idea what the original resistor value was. After replacing >resistor I check for AC ripple, saw 100mV so I assumed diode was OK. I will >change it anyway and let you all know. One thing to note, I observed only >13.6 volts feeding the LA7838 (it should be around 24V). I seperated the >vertical PS from the LA7838 and the voltage came back up to 40V (unloaded). >Something is loading this voltage down causing stress on the 10 ohm resistor >again, I'm starting to see brown marks appear on the new resistor. Maybe the >yoke is gone? > >David Lessard >mrfixit@xxxxxxxxxxx > >-----Original Message----- >From: techassist-bounce@xxxxxxxxxxxxx >[mailto:techassist-bounce@xxxxxxxxxxxxx]On Behalf Of Jeff Dougherty >Sent: Thursday, December 12, 2002 9:33 PM >To: techassist@xxxxxxxxxxxxx >Subject: [TechAssist] Re: Phillips 25P1-02 chassis - Model# PK4485 >(CH03) > > > >David, >Check for LEAKY D502 (PN: 4835-130-37048) >Good luck. >support@xxxxxxxxxxxxxxxxxx >FAX 717-564-4952 >Jeff Dougherty >Intrepid Video & Electronics Be careful of your thoughts. >501 Luther Rd They may become your words >Harrisburg, PA 17111 any moment. >717-909-8844 >VCR tips, electronics info & general interest. >www.intrepid-video.com www.tech-repair.net >www.thetoolcaddy.com www.9-11-2001tragedy.com >*********************************************************************** > >----- Original Message ----- >From: "David Lessard" <mrfixit@xxxxxxxxxxx> >To: <techassist@xxxxxxxxxxxxx> >Sent: Thursday, December 12, 2002 11:12 AM >Subject: [TechAssist] Phillips 25P1-02 chassis - Model# PK4485 (CH03) > > > >Gentlemen, > >Vertical size is only 6" (in the center), replaced (5) caps in vertical >circuit and LA7838, problem still there. Vertical adjust has minimal effect >on size. Something in the sync seperation circuit? Schematic would come in >real handy. > >Thanks. > >David Lessard >Alexandria Electronics >50 Harrison Street >Alexandria, Ontario >(613)525-4502 >mrfixit@xxxxxxxxxxx >------------------------------------------ >Submit A Repair Tip For Everyone Here: >http://www.tech-assist.org/secure/tip/main.html >------------------------------------------ >To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html >To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > > > >------------------------------------------ >Submit A Repair Tip For Everyone Here: >http://www.tech-assist.org/secure/tip/main.html >------------------------------------------ >To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html >To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > >------------------------------------------ >Submit A Repair Tip For Everyone Here: >http://www.tech-assist.org/secure/tip/main.html >------------------------------------------ >To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html >To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > > Peggs' Electronics 1519 West 2nd Street Owensboro,KY 42301 270-926-4968 fax 270-686-7399 ------------------------------------------ Submit A Repair Tip For Everyone Here: http://www.tech-assist.org/secure/tip/main.html ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.techassist.net/forms/change.html