Bob, As requested, the voltages in IC 51 are as follows: p1=1.35v p2=1.34v p3=1.34v p4=0v p5=1.34v p6=198.7v p7=49.2v p8=57.6v p9=43.1v I don't show any video present whatsoever on any of the pins of IC200. Now I seem to be loosing a little ground on it. It is now giving a raster that progressively gets brighter and is going into shutdown. I rechecked the resistors on the crt board and found none bad. Daryl Daryl's TV 3310 Dyer St. El Paso, TX 79930 915-565-9184 915-564-1024 Fax http://dynacomp.freeyellow.com -----Original Message----- From: Gemini Computer & TV <geminitv@xxxxxxxxxxxxxxxx> To: techassist@xxxxxxxxxxxxx <techassist@xxxxxxxxxxxxx> Date: Thursday, December 26, 2002 8:07 AM Subject: [TechAssist] Re: Magnvox, 27TP83, ch. 27v505, no video > >First, >Give us the voltage readings on all 9 pins of IC51 on the CRT board. Pins >1,2, and 3 are the R,G, and B inputs respectively (pins 7,8, and 9 are the >outputs). Also scope the inputs to see if you have video coming in. If not >then the video comes from IC200 (pins 21, 20, and 19 are R,G,B >respectively). This should get you started. > >Bob Waterman, CET® #RI-28 >Master Technician License #9109 >Service Manager >Gemini Computer, TV, & Security Alarms >(508)695-7302 >(508)695-7769 FAX >geminitv@xxxxxxxxxxxxxxxx >geminitv@xxxxxxx > >----- Original Message ----- >From: "D Thunhurst" <dthunhurst@xxxxxxx> >To: "TechAssist" <TechAssist@xxxxxxxxxxxxx> >Sent: Thursday, December 26, 2002 9:05 AM >Subject: [TechAssist] Magnvox, 27TP83, ch. 27v505, no video > > >> >> Good morning. >> I hope everyone had a merry Christmas. >> I am still having some problems with this set. Originally it came in with >> sound and no vert. deflection, in on both sides about 3 inches and would >> shut down after a few seconds. >> I replaced R464 (went high in value), IC401 (9 volt reg), and IC550 (vert. >> output). Now, I still have sound, full deflection both vertically and >> horizontally, bright raster with full retrace lines and no video. I have >> the 200 volts to the crt board and all of the resistors check ok on that >> board. I could use a little advice on this one as I don't have the >> schematic and Sams doesn't list anything one it. Tritronics list a manual >> for it but at $60 plus shipping is out of the question. I am leaning >> towards jungle chip but not sure as this is a guess. >> Thanks, >> Daryl >> Daryl's TV >> 3310 Dyer St. >> El Paso, TX 79930 >> 915-565-9184 >> 915-564-1024 Fax >> http://dynacomp.freeyellow.com >> >> ------------------------------------------ >> Submit A Repair Tip For Everyone Here: >> http://www.tech-assist.org/secure/tip/main.html >> ------------------------------------------ >> To REMOVE your email address, click here: >> http://www.tech-assist.org/unsubb.html >> To CHANGE your email address, click here: >> http://www.techassist.net/forms/change.html >> >> > >------------------------------------------ >Submit A Repair Tip For Everyone Here: >http://www.tech-assist.org/secure/tip/main.html >------------------------------------------ >To REMOVE your email address, click here: > http://www.tech-assist.org/unsubb.html >To CHANGE your email address, click here: > http://www.techassist.net/forms/change.html > > ------------------------------------------ Submit A Repair Tip For Everyone Here: http://www.tech-assist.org/secure/tip/main.html ------------------------------------------ To REMOVE your email address, click here: http://www.tech-assist.org/unsubb.html To CHANGE your email address, click here: http://www.techassist.net/forms/change.html