--------------------------------------------------------------- Text pasted from WinSTIPS 2.0 http://www.ServiceSoftware.com --------------------------------------------------------------- PHILIPS P1 B+ Low. No Raster. Danny Willard Replace Ic 400.( Opto-Coupler) --------------------------------------------------------------- PHILIPS P1 Dead Simpson'S Tv 25p1 R429, C430 --------------------------------------------------------------- PHILIPS P1 Dead Electronic Horizons Q420, Ic401, C430 .001/400, D430 Ecg580, R424 --------------------------------------------------------------- PHILIPS P1 Dead Billdog 20p1 Z434 --------------------------------------------------------------- PHILIPS P1 Dead Q420, R424, C430 1000pf/400v --------------------------------------------------------------- PHILIPS P1 Dead Colonial Tv Q450 Shorted 4835 130 47063 And R449 Open 24 Ohms --------------------------------------------------------------- PHILIPS P1 Dead Blue Ribbon Tv & Computers Replace C423 (47uf @ 50v) May Check Good With Fluke, But Has High Esr. --------------------------------------------------------------- PHILIPS P1 Dead Q420 6105590k01, R424 0.27-1w 4835 1165 7056 --------------------------------------------------------------- PHILIPS P1 Dead (Common Parts) Q502 (2sd1555, Philips# 483513047835) Q420 (Philips# 483513047068) R424 (0.27 Ohm / 1 Watt, Philips# 483511657056) C430 (1000pf, 400v, Philips# 483512147034) D430 (Mur460, Philips# 483513037488) R429 (24 Ohm / 3 Watt, Philips# 483511657043) Ic401 (Philips# 483520987071) C504 (10nf / 1.5kv, Philips# 483512147048) C505 (680pf / 2kv, Philips# 483512247037) Note: Some Of These Values May Differ For Different Screen Sizes, But The Ones Listed Above Are For The 27" Set. Remember To Change R427 And R428 Regardless Of How They Read. These Are Current Sense And Usually Go Off Value When Q420 Shorts. Don'T Measure Them, Just Change Them. Either .18 Or .2 Ohm Depending On Screen Size. --------------------------------------------------------------- PHILIPS P1 Dead - No Sound Or Picture Click Only Bryn Mawr Tv R429 P/N 483511657043 (24 Ohm/ 3watt) C430 P/N 483512147034 (1000pf/400volt Poly) D430 P/N 483513037061 (Mor-460) C505 P/N 483512257032 (470pf/2kv) --------------------------------------------------------------- PHILIPS P1 Dead Intermittantly After Repairing Regulator Gary D. Bombard Action Tv Systems Check C418 And C421. Caps Touching Resistors And Have Become Baked. --------------------------------------------------------------- PHILIPS P1 Dead Set, C505 Burnt... D.A. Electronics C505, C430, D430, R429, R424 And Switching Fet. Hot Was Ok. --------------------------------------------------------------- PHILIPS P1 Dead, No Click, Standby Voltages Down Marshfield Tv Replace C423, C435, C459, And C382, Electrolytic Caps In The Standby Circuit. See Sam'S 2741-1 --------------------------------------------------------------- PHILIPS P1 Dead, No Sound Or Pix, No Fuses Blown Larrys Tv Replace Open R424 (.27 Ohms) Shorted C430 (1000uf @400vdc) & Shorted Q420 (6105590001) Or 483513047062. --------------------------------------------------------------- PHILIPS P1 Dead. Replace Q502 ( H.O.T. ) And C505 ( 680pf2kv ) --------------------------------------------------------------- PHILIPS P1 Dead. Check Standby Chopper. Must Be Running Or Full Pwr Reg Won'T.. Osage Tv Start. If Problem With Micro Suspected Check Q433-B... If Base Is High (0.7v) Tv Is Held Off. Remove Solder From Base & Tv S Hould Come On. If So Goto Micro Pin 19 Is It 2v? Cange When Power Butt On Pressed? If No Change Check Pin 42vcc & Pin 33 Reset. Must Be 5v. --------------------------------------------------------------- PHILIPS P1 Dead. D430 Repeat Failure K&K T50w Ihvt P/N 4835 140 67003 (25" 26"), 4835 140 67002 (19" & 20") --------------------------------------------------------------- PHILIPS P1 Dead. If Q433-B Is Low (0v) And Tv Is Not Running, Go To Ic401-15.. Osage Tv If Pin 15 Is 5v And 4&5 Are Low (.2 Or ..1v) The Full Power Reg Is Held Off. Ic402 Xstr Section Is Pulling Volt Down. Isolate Ic40 2-5 If Full Power Restored Ic402,Q432, Q434. Also Any Part That Pulls Ic380'S 10v Too Low: Q430, Z430, Z434. --------------------------------------------------------------- PHILIPS P1 Dead. If Standby Is Running And Full Power Does Not Come Up Even... Osage Tv Though Ic402-5 Goes High (May Go To 6.8vdc) Check For.... Drive At Ic401-7 Aha!! It'S There Isn'T It? B+ To F.P. Fet Is Being Lo St Due To A Bad Solder Connection At L421 Or Somewhere Else. --------------------------------------------------------------- PHILIPS P1 Dead. No Relay Click Duncanville Tv & Video R424 Open .27ohm 1/2 Watt Ic401 Control Ic Pt# 483520987071 Also Net1765 --------------------------------------------------------------- PHILIPS P1 Dead. Pcb Burned At D430 Kirk Flushing Mi D430 Shorted, Q420, Burned C430, Open R429, R424 --------------------------------------------------------------- PHILIPS P1 Lightning Damaged, Dead Set... D.A. Electronics Q420, R424, R427, R428, R422, R449, R428, IC400, IC401, IC402 and Q450. To test Main Supply out of Cabinet Remove R505 and Shunt Q433 Base to Ground. --------------------------------------------------------------- PHILIPS P1 Operation: Power Would Come On Middle Of Night, Full Volume Static And Full Bright White Screen Atv Ic380 (5 V Reg Ic) To The Mpu Had Very Loose Connection On The Output Pin. --------------------------------------------------------------- PHILIPS P1 Parts: C504 The Service Manual Lists It As A 10nf, 5%, 1.5kv, Polypropylene With Part Number 483512147048 --------------------------------------------------------------- PHILIPS P1 Power Off Inop (Set Stays On) First Thing To Do Is Replace Ic402 (Optoisolator Ic). It Is Part # 483513097005 (Formerly Part# 5303000001). If That Does Not Take Care Of It, Then Check Z430, C421, C430, R427, R428, Q433, And Ic400. --------------------------------------------------------------- PHILIPS P1 Power Off Inop (Set Stays On) I Found R446 Off Of The Base Of Q433 That Went To P19 Of The Micro Bad. Although It Checked Well Within Tolerance It Must Have Been Breaking Down Under Load. Subbed Another One In Its Place And It Worked. However, The Base Voltage On Q433 Did Not Change But The Collector Voltage Was Greatly Changed When In The "Off" State. --------------------------------------------------------------- PHILIPS P1 Power Off Inop (Set Stays On).. Cap'S Ic402, Photooptic Isolator (Ecg3041) 5303000001 --------------------------------------------------------------- PHILIPS P1 Power Supply - 130v Varies Dmac1054@xxxxxxx R427, R428, Ic400 --------------------------------------------------------------- PHILIPS P1 Power Supply - B+ Low Or High Dmac1054@xxxxxxx Z430 --------------------------------------------------------------- PHILIPS P1 Power Supply Burned At C430 Tvdr Check For Shorted C430 Change To 1000wvdc To Withstand Extra Stress --------------------------------------------------------------- PHILIPS P1 Shutdown, Immediate At Turn On Peggs R430 110k Resistor Increased To 130k. Causing Ic402 Circuit To Trigger Shut Off. 130v Was Too High --------------------------------------------------------------- PHILIPS P1 Standby 5v takes several minutes to come up Audio Video Clinic Chassis: 27p1-01 C456, C459, C441, C423 --------------------------------------------------------------- PHILIPS P1 Startup Inop Q420 6105590k01, R427 &428 Exact Val,C430,R429, Ic400,401,402 --------------------------------------------------------------- Bob Waterman, CET® #RI-28 Master Technician License #9109 Service Manager / Parts Manager Gemini Computer, TV, & Security Alarms (508)695-7302 (508)695-7769 FAX geminitv@xxxxxxxxxxx geminitv@xxxxxxx www.geminicomputertvsecurityalarms.com ----- Original Message ----- From: "armando guerra" <birdie@xxxxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Wednesday, August 04, 2004 11:08 PM Subject: [TechAssist] Magnavox TV Model RK5556/27P1 chasis.No start problem. > This set came in dead.No relay action at all.Fuse is ok.I can't find my > sm for this set but while checking around ,I found R 429 open and C430 > shorted. I used a 24 ohm for 429 and a 1000pf\400v cap for 430.Also > resoldered alot of cold solders which is very common on this > chasis.Still no relay click at all.Just going from memory,I think that > IC380 is the 5v reg.I checked for the vcc coming in to the ic but its > very low.its only 2.7v.The IR and pin 42 of the micro is also at 2.7v > instead of the 5v.Can someone please send me a pdf file of the power > supply on this tv so that I can locate the missing voltages.I told the > customer that it was already 14yrs old but she said that if I could fix > it,she would apreciate it very much since it was her husband's favorite > tv.He passed away last yr. > Thanks for your help. > Mando > Birdie's TV & Electronics > Casa Grande, AZ > > > -------------------------------------------------------------------------- --- > Lost Password: > http://www.tech-assist.org and select "Login Problems?". > Email Archives: > //www.freelists.org/archives/techassist/ ----------------------------------------------------------------------------- Lost Password: http://www.tech-assist.org and select "Login Problems?". Email Archives: //www.freelists.org/archives/techassist/