Is it the one Eric was using ? Le 24.03.2012 04:44, John Douyere a écrit :
Yes, in the test alpha versions with the new modes. 73, John On 24/03/2012 12:33 PM, "remi.chateauneu@xxxxxxxxx <mailto:remi.chateauneu@xxxxxxxxx>" <remi.chateauneu@xxxxxxxxx <mailto:remi.chateauneu@xxxxxxxxx>> wrote: There's a fldigi internal queue whose size has to be increased. There was a talk about this.? Probably, John already applied these changes somewhere: <mailto:remi.chateauneu@gmail. <mailto:remi.chateauneu@gmail.>__**com <remi.chateauneu@xxxxxxxxx <mailto:remi.chateauneu@xxxxxxxxx>>>> wrote: >> > >> > Hi again John, >> > >> > Probably, a processing queue cannot be emptied quickly enough. >> > Apart from speeding up your code, you might try these changes, they >> may help a bit: >> > >> > (1) >> > qrunner.h >> > LOG_ERROR("qrunner: thread %" PRIdPTR " fifo full!", GET_THREAD_ID()); >> > Replaced by; >> > LOG_ERROR("qrunner: thread %" PRIdPTR " fifo full at %s!", >> GET_THREAD_ID(),typeid(F).**__name() ); >> > >> > So that we will see with which function it happens. >> > >> > (2) >> > src/qrunner/qrunner.cxx: >> > #define FIFO_SIZE 2048 >> > Replaced by; >> > #define FIFO_SIZE 8192 >> > >> > So that the queue will be bigger and might leave enough time for >> processing. >> > >> > (3) >> > ./configure --enable-optimizations=native >> > >> > This should produce a code with better instructions. >> > >> > (4) >> > In m4/opt.m4 >> > >> > OPT_CFLAGS="-O2 -ffast-math -finline-functions" >> > >> > Replaced by >> > >> > OPT_CFLAGS="-O3 -ffast-math -finline-functions" >> > >> > As well, the code should be slightly faster. >> > >> > Hope this helps. >> > >> > Cheers >> > >> > Remi >> Le 23.03.2012 19:36, Eric Davenport a écrit : I have some more information that may be important or a guidance to all. JPSKMail ran for a number of hours today and then FLDIGI froze and created a 250Meg Status_Log.TXT Most of it was filled with the following. I: apply: RSID: PSK250R @ 1044 Hz I: apply: RSID: PSK250R @ 1044 Hz I: ParseMode: ARQ new modem set to PSK250R I: ParseMode: ARQ new modem set to PSK250R I: apply: RSID: PSK250R @ 1050 Hz I: ParseMode: ARQ new modem set to PSK250R I: ParseMode: ARQ new modem set to PSK250R I: apply: RSID: PSK250R @ 1050 Hz I: apply: RSID: PSK250R @ 1044 Hz I: apply: RSID: BPSK250 @ 1050 Hz I: apply: RSID: PSK250R @ 1044 Hz E: request: qrunner: thread 0 fifo full! E: request: qrunner: thread 0 fifo full! E: request: qrunner: thread 0 fifo full! E: request: qrunner: thread 0 fifo full! E: request: qrunner: thread 0 fifo full! E: request: qrunner: thread 0 fifo full! E: request: qrunner: thread 0 fifo full! E: request: qrunner: thread 0 fifo full! E: request: qrunner: thread 0 fifo full! and this went of till I stopped it at 250 megs. Hope this helps us.