Hi Carlos. The third Radio Button on the Basics Sheet is titled "Tutor Messages, Announce Customer Messages Only" I checked this and rebooted but still I get the Read Only message. Best wishes. Andy ----- Original Message ----- From: "Carlos Vallejo" <carlos.vallejo@xxxxxxxxxxxxxxx> To: <jaws-uk@xxxxxxxxxxxxx> Sent: Wednesday, December 13, 2006 6:57 PM Subject: [jaws-uk] Re: JAWS 60 acting up > Hi Andy > to get rid of the < read only message > you have to go to the Jaws window, > press enter and when the options window opens, go down once with the down > arrow. Once you're in basic settings dialogue box, press enter. There > you'll be in a window with three radio buttons. Check the bottom one and > that should do it. > Good luck, > > Carlos. > ----- Original Message ----- > From: "Andy Logue" <andy@xxxxxxxxxxxxxxxxxxxxxxxxx> > To: <jaws-uk@xxxxxxxxxxxxx> > Sent: Wednesday, December 13, 2006 11:41 AM > Subject: [jaws-uk] Re: JAWS 60 acting up > > >> Hi David. >> >> I'll need sighted assistance to try this out, so I'll have to wait until >> later tonight until Pauline comes home. >> >> Can you tell me how to get into both the Speech and Sounds Manager and >> also, >> the Configuration Manager. If I can get into them, then Pauline can read >> me >> through your instructions. >> >> Thanks. >> >> Best wishes. >> Andy >> >> ----- Original Message ----- >> From: "David" <david.tregellas@xxxxxxxxxxxx> >> To: <jaws-uk@xxxxxxxxxxxxx> >> Sent: Wednesday, December 13, 2006 10:12 AM >> Subject: [jaws-uk] Re: JAWS 60 acting up >> >> >>> Hi Andy, >>> >>> You may be able to get rid of the "Read Only" thing by going into Speech >>> and >>> Sounds Manager. >>> >>> Get into your Configuration |Manager, Set Options then Speech and Sounds >>> Manager. Tab twice to an Edit button and press enter. Do a control tab >>> and >>> then press "R" once or twice and it will say "?Read Only". Tab twice I >>> think and cursor up or down until you find "Ignore". Activate this and >>> exit >>> in the usual way. Hopefully, that should work. >>> >>> As for your second point I can't answer that but I can't delete from >>> inside >>> a message either. >>> >>> Point three. Go to your Verbosity Options with insert V and you should >>> find >>> "Announce Header fields with Message" and this should be set to off. >>> When >>> you then go into a message it should start immediately with the message. >>> >>> I'm often wrong about these things but best of luck anyway. >>> >>> Regards >>> >>> David >>> >>> >>> -----Original Message----- >>> From: jaws-uk-bounce@xxxxxxxxxxxxx >>> [mailto:jaws-uk-bounce@xxxxxxxxxxxxx]On Behalf Of Andy Logue >>> Sent: 12 December 2006 19:49 >>> To: jaws-uk@xxxxxxxxxxxxx >>> Subject: [jaws-uk] JAWS 60 acting up >>> >>> >>> Hi all. >>> >>> Not sure if my earlier message on this matter got through, so >>> re-posting. >>> >>> I had to reinstall JAWS version 6.0 yesterday into my XP Home Edition >>> computer after it crashed badly a few weeks ago. I'm using Internet >>> Explorer version 6. >>> >>> The problems: >>> >>> When I open a message, JAWS announces, within the text of the message, >>> Read >>> Only. >>> >>> I am also unable to delete the message from within, by pressing the del >>> key. >>> When I attempt this, JAWS beeps. >>> >>> Also, I normally, when opening a message, press tab a couple of times, >>> to >>> get to the main body and prevent the need to read the above headers. >>> Well, >>> I am no longer able to do this and when I attempt to do so, JAWS beeps >>> when >>> I press the tab key. >>> >>> It also appears that when I open a message, JAWS is at the bottom >>> because >>> I >>> hear often Original Message, prior to anything else. >>> >>> Any advise would be very welcome as this is driving me crazy. >>> >>> Best wishes. >>> Andy >>> >>> >>> ** To leave the list, click on the immediately-following link:- >>> ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] >>> ** If this link doesn't work then send a message to: >>> ** jaws-uk-request@xxxxxxxxxxxxx >>> ** and in the Subject line type >>> ** unsubscribe >>> ** For other list commands such as vacation mode, click on the >>> ** immediately-following link:- >>> ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=faq] >>> ** or send a message, to >>> ** jaws-uk-request@xxxxxxxxxxxxx with the Subject:- faq >>> >>> ** To leave the list, click on the immediately-following link:- >>> ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] >>> ** If this link doesn't work then send a message to: >>> ** jaws-uk-request@xxxxxxxxxxxxx >>> ** and in the Subject line type >>> ** unsubscribe >>> ** For other list commands such as vacation mode, click on the >>> ** immediately-following link:- >>> ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=faq] >>> ** or send a message, to >>> ** jaws-uk-request@xxxxxxxxxxxxx with the Subject:- faq >>> >>> >> >> >> ** To leave the list, click on the immediately-following link:- >> ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] >> ** If this link doesn't work then send a message to: >> ** jaws-uk-request@xxxxxxxxxxxxx >> ** and in the Subject line type >> ** unsubscribe >> ** For other list commands such as vacation mode, click on the >> ** immediately-following link:- >> ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=faq] >> ** or send a message, to >> ** jaws-uk-request@xxxxxxxxxxxxx with the Subject:- faq >> > > > ** To leave the list, click on the immediately-following link:- > ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] > ** If this link doesn't work then send a message to: > ** jaws-uk-request@xxxxxxxxxxxxx > ** and in the Subject line type > ** unsubscribe > ** For other list commands such as vacation mode, click on the > ** immediately-following link:- > ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=faq] > ** or send a message, to ** jaws-uk-request@xxxxxxxxxxxxx with the > Subject:- faq > > ** To leave the list, click on the immediately-following link:- ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=unsubscribe] ** If this link doesn't work then send a message to: ** jaws-uk-request@xxxxxxxxxxxxx ** and in the Subject line type ** unsubscribe ** For other list commands such as vacation mode, click on the ** immediately-following link:- ** [mailto:jaws-uk-request@xxxxxxxxxxxxx?subject=faq] ** or send a message, to ** jaws-uk-request@xxxxxxxxxxxxx with the Subject:- faq