[PCB_FORUM] Re: Shorting two or more nets together

  • From: "TEYSSIER Jean-Charles" <jcteyssier@xxxxxxxxxxxxxxx>
  • To: <icu-pcb-forum@xxxxxxxxxxxxx>
  • Date: Tue, 10 Jan 2012 16:55:09 +0100

Ouch....... Verry dangerous.

 

It is kind of property i avoid to use (it allow ALL drc's with all nets)

 

Jean-Charles TEYSSIER 

Responsable d'affaire

Adeneo 

Adetel Group

2, chemin du Ruisseau 
69134 ECULLY - FRANCE
Tél:+33(0)4 26 49 04 09-Fax:+33(0)4 72 86 05 39

www.adetelgroup.com <http://www.adetelgroup.com/>    

P Before printing, think about ENVIRONMENTAL responsibility!

________________________________

De : icu-pcb-forum-bounce@xxxxxxxxxxxxx 
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] De la part de Macindoe, Gary
Envoyé : mardi 10 janvier 2012 16:50
À : icu-pcb-forum@xxxxxxxxxxxxx
Objet : [PCB_FORUM] Re: Shorting two or more nets together

 

My guess is that you could put a "No_Drc" property on the pin.

 

Regards,

 

Gary MacIndoe

Senior PCB Design Engineer

EbD R&D Hardware

Surgical Solutions Group

Covidien

5920 Longbow Drive

Boulder, CO 80301

 

303.476.7458

www.covidien.com

 

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx 
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Carrow, Dennis
Sent: Tuesday, January 10, 2012 8:38 AM
To: 'icu-pcb-forum@xxxxxxxxxxxxx'
Subject: [PCB_FORUM] Re: Shorting two or more nets together

 

So I follow the doc when building by symbol but I have pad to pad errors 
because I have via pads inside of a larger pad.  I see on figure 3 of the ap 
note they have pad to pad errors also.   So do I leave these errors or am I 
missing a step?  Thanks! -DC

 

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx 
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Gerry Meier
Sent: Monday, January 09, 2012 4:30 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: Shorting two or more nets together

 

Try this

 

Gerry Meier, Sr. PCB Designer

Freedom CAD Services. Inc

Voice: (256) 715-1424 

Email:gerry.meier@xxxxxxxxxxxxxx

Skype: rgmeier3

visit us at http://www.freedomcad.com <http://www.freedomcad.com/> 

 P  Think Green only print as needed. 

 

From: icu-pcb-forum-bounce@xxxxxxxxxxxxx 
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Carrow, Dennis
Sent: Monday, January 09, 2012 4:27 PM
To: 'icu-pcb-forum@xxxxxxxxxxxxx'
Subject: [PCB_FORUM] Shorting two or more nets together

 

Hi Everyone,

                Can I ask how to properly short two or more grounds at a common 
point using Cadence Allegro 16.X and Design Entry HDL?  Thanks for any and all 
ideas! DC

Other related posts:

  1. Home
  2. icu-pcb-forum
  3. Archive
  4. 01-2012