[PCB_FORUM] Re: Globally change to alt symbol across board

Hello again Gary,
Is this another 15.1 issue?
I could not get this to work.
Steps 1-3 work fine.
But step 4 does not.
I could not get RMB "alt sym" selection when moving symbol  by "symtype".
I tried with move by pin 1, user pick, origin and with / without "stretch"

Also, I have never been able to select "alt sym" when using temp group.

What am I missing?

Thanks again for your input!
Mark
Macindoe, Gary wrote:


Hey Mark,

So did you get my last post?  Did you ever get the searchable PDF to
work?

So, your latest problem is no big thing! Simply follow the steps below:

1) Get in the Move command

2) In the Find tab at right, in the "Find Buy Name" field, pull-down to
"Symtype", then click the More button.

3) In the window that comes up, choose the symbol name (i.e. "0603"),
then click OK (all of the chosen symbols in your design will highlight).

4) Now, click on a reference point (all of the symbols are "picked up"),
then RMB to "Alt Symbol", then click back on the reference point to set
all of the symbols down in their original location.


This will only work if you want *all* of a particular symbol type
changed to the alternate symbol.  If not, you could at least get into
the Move command, RMB to Temp Group, select all symbols you want with a
click, box or a combination of the two, then RMB to Complete, RMB again
to Alt Symbol, then put them down where they were.

Good luck!


Gary E. MacIndoe
PCB Design Engineer
Advanced Micro Devices
Longmont, Colorado

amd.com
gary.macindoe@xxxxxxx

-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Mark Salberg
Sent: Tuesday, December 05, 2006 1:33 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Globally change to alt symbol across board
Can I change all of my 500 relays to an alternate symbol across the whole board? 
The only way I can find to do it is thru delete / manual place or Move /

select alt sym the place back down.
Very very time consuming concidering this can not be done in "stretch
mode".
All my parts are on a 1 mil grid.

HELP!

Thanks,
Mark


________________________________________________________________________
_____
Scanned by IBM Email Security Management Services powered by
MessageLabs. For more information please visit http://www.ers.ibm.com
________________________________________________________________________
_____
-----------------------------------------------------------
To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx 
with a subject of subscribe or unsubscribe

To view the archives of this list go to
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------




-----------------------------------------------------------
To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx 
with a subject of subscribe or unsubscribe

To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------

_____________________________________________________________________________
Scanned by IBM Email Security Management Services powered by MessageLabs. For 
more information please visit http://www.ers.ibm.com
_____________________________________________________________________________




_____________________________________________________________________________
Scanned by IBM Email Security Management Services powered by MessageLabs. For 
more information please visit http://www.ers.ibm.com
_____________________________________________________________________________
-----------------------------------------------------------
To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx 
with a subject of subscribe or unsubscribe

To view the archives of this list go to 
http://www.freelists.org/archives/icu-pcb-forum/

Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------

Other related posts: