[PCB_FORUM] Re: Allegro 15.7 duplicate vias
- From: sjchar3@xxxxxxxxxxxx
- To: icu-pcb-forum@xxxxxxxxxxxxx
- Date: Thu, 08 Jul 2010 16:16:26 -0400
16.3 does via removals.
I too like this forum better than the cadence one. faster, leaner and most of
the time i get an answer.
sam
-----Original Message-----
From: Macindoe, Gary <Gary.Macindoe@xxxxxxxxxxxx>
To: icu-pcb-forum@xxxxxxxxxxxxx
Sent: Thu, Jul 8, 2010 10:14 am
Subject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias
Les,
Maybe the Dangling Lines Report (Tools -> Reports) will give you the
information
ou need.
Like Joe said, if there are two vias in the same location, you should get a DRC
rror.
Regards,
Gary MacIndoe
enior PCB Layout Designer
ontract - Kelly Services
ovidien
bD R & D
920 Longbow Drive
oulder, CO 80301
303.476.7458
ww.covidien.com
-----Original Message-----
rom: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx]
n Behalf Of Les Wong
ent: Thursday, July 08, 2010 9:17 AM
o: icu-pcb-forum@xxxxxxxxxxxxx
ubject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias
Jean-Charles
I looked in the dbdoctor.log file but did not see any duplicate via messages ?
es
-- On Thu, 7/8/10, JCharles TEYSSIER <jeancharles.teyssier@xxxxxxx> wrote:
> From: JCharles TEYSSIER <jeancharles.teyssier@xxxxxxx>
Subject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias
To: icu-pcb-forum@xxxxxxxxxxxxx
Date: Thursday, July 8, 2010, 2:22 AM
Dave,
i am also on cadence's community BUT _i_ considere this
"forum" more easyer to use each day...
I have respond to somebody on cadence's community; this
person rspond and when i try to respond ... the web site
does nor allow me to...(internal error)
I think i would retry later... this is not first time i
have problems with cadence's site
Emails NEVER fails; cadence's web site does.
And it bory me with log-in each time!
THIS place is much more easier. When cadence's community
site will be much more userfreindly (less flash animations,
more reliebality) it will be a real good place
Les,
dbdoctor generates a log file: you can find in it the
coordonates of duplicated vias so you can remove them
manually.
Jean-Charles
Les Wong a écrit :
> Hi Dave
> Thanks,
> Les
>
> --- On *Wed, 7/7/10, David Elder /<dave.elder@xxxxxxxxxxxxx>/*
wrote:
>
>
> From: David Elder <dave.elder@xxxxxxxxxxxxx>
> Subject: Re: [PCB_FORUM]
Allegro 15.7 duplicate vias
> To: icu-pcb-forum@xxxxxxxxxxxxx
> Date: Wednesday, July 7, 2010,
2:42 PM
>
> Hi Les,
> This forum doesn't
get much use any more. You might want to
> consider moving over to the
cadence community forum -
> http://www.cadence.com/community/forums/27.aspx
> Anyway - attached is
some code that identifies duplicate hits on
> holes and vias.
> Regards,
> Dave
>
> Dave Elder
> PCB Design Manager
> Tait Radio Communications
> 535 Wairakei Rd, PO Box 1645,
Christchurch
> DDI: +64 3 358-0327
> Mobile: +64 21 373725
> www.taitradio.com <http://www.taitradio.com>
> dave.elder@xxxxxxxxxxxxx
</mc/compose?to=dave.elder@xxxxxxxxxxxxx>
> TAIT: THE RIGHT FIT
>
>
> On 8 July 2010 06:10, Les Wong
<maveric0@xxxxxxxxxxx
> </mc/compose?to=maveric0@xxxxxxxxxxx>>
wrote:
>
> Hi All
>
> Dbcheck used to
removed duplicate vias, dbdoctor does not do
> this any more.
> How is everyone
dectecting and removing duplicate vias ?
>
> Thanks,
> Les
>
>
-----------------------------------------------------------
To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
-----------------------------------------------------------
----------------------------------------------------------
o subscribe/unsubscribe:
end a message to icu-pcb-forum-request@xxxxxxxxxxxxx
ith a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
end an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
----------------------------------------------------------
----------------------------------------------------------
o subscribe/unsubscribe:
end a message to icu-pcb-forum-request@xxxxxxxxxxxxx
ith a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
end an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
----------------------------------------------------------
Other related posts:
