Les, Maybe the Dangling Lines Report (Tools -> Reports) will give you the information you need. Like Joe said, if there are two vias in the same location, you should get a DRC error. Regards, Gary MacIndoe Senior PCB Layout Designer Contract - Kelly Services Covidien EbD R & D 5920 Longbow Drive Boulder, CO 80301 303.476.7458 www.covidien.com -----Original Message----- From: icu-pcb-forum-bounce@xxxxxxxxxxxxx [mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of Les Wong Sent: Thursday, July 08, 2010 9:17 AM To: icu-pcb-forum@xxxxxxxxxxxxx Subject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias Jean-Charles I looked in the dbdoctor.log file but did not see any duplicate via messages ? Les --- On Thu, 7/8/10, JCharles TEYSSIER <jeancharles.teyssier@xxxxxxx> wrote: > From: JCharles TEYSSIER <jeancharles.teyssier@xxxxxxx> > Subject: [PCB_FORUM] Re: Allegro 15.7 duplicate vias > To: icu-pcb-forum@xxxxxxxxxxxxx > Date: Thursday, July 8, 2010, 2:22 AM > Dave, > > i am also on cadence's community BUT _i_ considere this > "forum" more easyer to use each day... > > I have respond to somebody on cadence's community; this > person rspond and when i try to respond ... the web site > does nor allow me to...(internal error) > I think i would retry later... this is not first time i > have problems with cadence's site > > Emails NEVER fails; cadence's web site does. > And it bory me with log-in each time! > > THIS place is much more easier. When cadence's community > site will be much more userfreindly (less flash animations, > more reliebality) it will be a real good place > > Les, > > dbdoctor generates a log file: you can find in it the > coordonates of duplicated vias so you can remove them > manually. > > Jean-Charles > > Les Wong a écrit : > > Hi Dave > > Thanks, > > Les > > > > --- On *Wed, 7/7/10, David Elder /<dave.elder@xxxxxxxxxxxxx>/* > wrote: > > > > > > From: David Elder <dave.elder@xxxxxxxxxxxxx> > > Subject: Re: [PCB_FORUM] > Allegro 15.7 duplicate vias > > To: icu-pcb-forum@xxxxxxxxxxxxx > > Date: Wednesday, July 7, 2010, > 2:42 PM > > > > Hi Les, > > This forum doesn't > get much use any more. You might want to > > consider moving over to the > cadence community forum - > > http://www.cadence.com/community/forums/27.aspx > > Anyway - attached is > some code that identifies duplicate hits on > > holes and vias. > > Regards, > > Dave > > > > Dave Elder > > PCB Design Manager > > Tait Radio Communications > > 535 Wairakei Rd, PO Box 1645, > Christchurch > > DDI: +64 3 358-0327 > > Mobile: +64 21 373725 > > www.taitradio.com <http://www.taitradio.com> > > dave.elder@xxxxxxxxxxxxx > </mc/compose?to=dave.elder@xxxxxxxxxxxxx> > > TAIT: THE RIGHT FIT > > > > > > On 8 July 2010 06:10, Les Wong > <maveric0@xxxxxxxxxxx > > </mc/compose?to=maveric0@xxxxxxxxxxx>> > wrote: > > > > Hi All > > > > Dbcheck used to > removed duplicate vias, dbdoctor does not do > > this any more. > > How is everyone > dectecting and removing duplicate vias ? > > > > Thanks, > > Les > > > > > ----------------------------------------------------------- > To subscribe/unsubscribe: Send a message to > icu-pcb-forum-request@xxxxxxxxxxxxx > with a subject of subscribe or unsubscribe > > To view the archives of this list go to > //www.freelists.org/archives/icu-pcb-forum/ > > Problems or Questions: > Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx > ----------------------------------------------------------- > ----------------------------------------------------------- To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or unsubscribe To view the archives of this list go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx ----------------------------------------------------------- ----------------------------------------------------------- To subscribe/unsubscribe: Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx with a subject of subscribe or unsubscribe To view the archives of this list go to //www.freelists.org/archives/icu-pcb-forum/ Problems or Questions: Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx -----------------------------------------------------------