PF3 and ActiveSky 2016 are probably two of the best purchases I have made for
FSX. Sim Physics is in there as well, and tonight, I managed to lose my brakes
because dodo bird me apparently did not plug my rudder pedals in, and the
trigger on my joystick is not a two position one, which means squeezing it
applies the brakes fully.
Jordan
-----Original Message-----
From: bvipilots-bounce@xxxxxxxxxxxxx [mailto:bvipilots-bounce@xxxxxxxxxxxxx] On ;
Behalf Of Zachary Kline
Sent: Wednesday, February 1, 2017 12:25 AM
To: bvipilots@xxxxxxxxxxxxx
Subject: [bvipilots] Re: Just crashed flying into KABQ using PF3
Yeah, the fact that you can adjust those specs is pretty neat. You can save
presets for multiple types of aircraft, which is helpful if you don’t have a
preferred one. I should remember to do that more often.
On Jan 31, 2017, at 10:11 PM, Jordan Gallacher <jordanandseptember@xxxxxxxxx>
wrote:
Looks like I set PF3 wrong. The two flights I did today went perfectly. I
even had to declare an emergency since I was almost bingo on fuel. The trick
with PF3 appears to be that it has to be setup as close to what the airplane
specs are for climbing, descending, and approach speed in the boxes when in
the load a flight plan window. Videos will probably start being made
tomorrow or Thursday, and anyone wishing to see PF3 in action will be able to
do so.
Jordan
-----Original Message-----
From: bvipilots-bounce@xxxxxxxxxxxxx
[mailto:bvipilots-bounce@xxxxxxxxxxxxx] On Behalf Of Joshua Tubbs
Sent: Tuesday, January 31, 2017 11:10 PM
To: bvipilots@xxxxxxxxxxxxx
Subject: [bvipilots] Re: Just crashed flying into KABQ using PF3
It's unfortunate that MSATC works the best, because well, it's 10 years or so
out of date. Dovetale's sim, while probably not accessible--the interface
that is, will apparently work with addons that work with FSX.
Here's hoping that IYP will work with it given this information.
On 1/31/17, Jordan Gallacher <jordanandseptember@xxxxxxxxx> wrote:
Going to have to try again with different settings on PF3. I have aBlind and Visually impaired Pilots mailinglist
suspicion that I did not setup things correctly because I had similar
problems last night flying from KABQ to KPHX where I ended up much
too close to the airport without any runway to expect to land on.
Jordan
From: bvipilots-bounce@xxxxxxxxxxxxx
[mailto:bvipilots-bounce@xxxxxxxxxxxxx]
On Behalf Of Robert Cezar
Sent: Tuesday, January 31, 2017 1:18 PM
To: bvipilots@xxxxxxxxxxxxx
Subject: [bvipilots] Re: Just crashed flying into KABQ using PF3
Hi,
I conducted the same flight in a Boeing 738 (I do not have an Embraer
190 on my development PC) using MS-ATC and the flight was perfectly
normal (see attached CVRT). The ACARS PIREP was also uploaded.
r
On Sun, Jan 29, 2017 at 8:08 PM, Jordan Gallacher
<jordanandseptember@xxxxxxxxx> wrote:
I was flying a Embraer 190 into KABQ, and was going to be landing on
runway 3. PF3 was working pretty well except for telling me to
descend to 15,000ft much too early. IYP was the issue this time
around since it switched to ILS Approach mode too soon and too close
to the airport. Thus, I ended up crashing onto a hill somewhere in the
ballpark of 5 miles from the airport.
Jordan
//www.freelists.org/list/bvipilots
To post a message to the list, send a message to bvipilots@xxxxxxxxxxxxx To
unsubscribe, send a message to bvipilots-request@xxxxxxxxxxxxx and put the
word unsubscribe in the subject of your message.
For other options such as digest, send a message to
bvipilots-request@xxxxxxxxxxxxx and put the word help in the subject of your
message.
Blind and Visually impaired Pilots mailinglist
//www.freelists.org/list/bvipilots
To post a message to the list, send a message to
bvipilots@xxxxxxxxxxxxx To unsubscribe, send a message to
bvipilots-request@xxxxxxxxxxxxx and put the word unsubscribe in the subject
of your message.
For other options such as digest, send a message to
bvipilots-request@xxxxxxxxxxxxx and put the word help in the subject of your
message.
