[TechAssist] Re: Zenith PROJO PVR 5263 distorted pix
- From: <tvservice@xxxxxxxxxxxxx>
- To: <techassist@xxxxxxxxxxxxx>
- Date: Thu, 1 May 2003 09:26:01 -0500
Do you have the back covered well?
may be room light coming thru from back
Robert
tvservice@xxxxxxxxxxxxx
H & H Electronics Inc
----- Original Message -----
From: "Bill Boyd" <billstvs@xxxxxxxxxx>
To: <techassist@xxxxxxxxxxxxx>
Sent: Thursday, May 01, 2003 12:03 AM
Subject: [TechAssist] Re: Zenith PROJO PVR 5263 distorted pix
>
> Remove the screen and turn it upside down. See if the distortion moves
with
> the screen.
> I once had one that had a coffee cup stain between the two halves of the
> screen.
> I couldn't see it until I separated the screens but the customer could.
> It came from the factory that way.
> If the distortion is still at the top remove the lens and check the
coolant
> level and the face of the tubes for burns.
>
> HTH
> Bill
> Bill's TV Service
> Sulphur Springs, TX
>
>
>
> >From: "Bill Dravenstott" <cdravens@xxxxxxxxxx>
> >To: <techassist@xxxxxxxxxxxxx>
> >Subject: [TechAssist] Re: Zenith PROJO PVR 5263 distorted pix
> >Date: Thu, 1 May 2003 00:07:28 -0400
> >
> >
> >No effect by vertical adjustment. The picture looks ok as far as size
and
> >shape, but the light area is about 6inches long and 1.5 inches at the
widest
> >point. Just like a bleached lighter area in the odd shape over the
picture.
> >
> >Bill Dravenstott
> >Elza's Home Store, LTD
> >Ashland, OH
> >419-289-8864
> >cdravens@xxxxxxxxxx
> >----- Original Message -----
> >From: "Jorge Camboni" <geo@xxxxxxxxxxxxx>
> >To: <techassist@xxxxxxxxxxxxx>
> >Sent: Wednesday, April 30, 2003 10:21 PM
> >Subject: [TechAssist] Re: Zenith PROJO PVR 5263 distorted pix
> >
> >
> > >
> > > Try increasing the vertical size a little..
> > >
> > > Jorge
> > >
> > >
> > >
> > > At 09:17 p.m. 30/04/03 -0400, "Bill Dravenstott" <cdravens@xxxxxxxxxx>
> >wrote:
> > > >Hi all,
> > > >
> > > >This set came in with a picture that looked like severe pincushion
> > > >problem. I found the 26volt source to convergence (9-1318-2)
> > > >missing. Repaired power supply(9-1302-7) now set has a light color
at
> > > >top. I will call it a smile shape. It is most noticeable with a
light
> > > >background. No matter if any guns are covered the distortion remains.
> > > >
> > > >I can't discover any distortions in voltages. There is no
sensitivity to
> > > >cold or heat. Any ideas where to look?
> > > >
> > > >Bill Dravenstott
> > > >Elza's Home Store, LTD
> > > >Ashland, OH
> > > >419-289-8864
> > > >cdravens@xxxxxxxxxx
> > >
> >
>***************************************************************************
>
>
****************************************************************************
*
> The Tech Address Book:
> http://www.tech-assist.org/secure/tip/contact.html
> Add a Repair Tip Here, or Change/Remove your Email Address:
> http://www.tech-assist.org/secure/tip/main.html
> Lost Password:
> http://www.tech-assist.org and select "Lost your Login Info?".
> Email Archives:
> //www.freelists.org/archives/techassist/
*****************************************************************************
The Tech Address Book:
http://www.tech-assist.org/secure/tip/contact.html
Add a Repair Tip Here, or Change/Remove your Email Address:
http://www.tech-assist.org/secure/tip/main.html
Lost Password:
http://www.tech-assist.org and select "Lost your Login Info?".
Email Archives:
//www.freelists.org/archives/techassist/
Other related posts:
