[TechAssist] Re: Sony VCR SLV-360, cassette goes in and come right back out
- From: Gary McCartney <gary@xxxxxxxxxxx>
- To: techassist@xxxxxxxxxxxxx
- Date: Wed, 04 Dec 2002 14:47:48 -0500
Hi Jerry.
Thanks very much for your reply. Appreciated.
Yes, I found the problem. The new FL gear I bought is slightly different
than the original gear. It has differnetly shaped flanges on it which
prevent the large black loading gear from rotoating far enough to engage
the teeth on the slide plate. Put the original gear back in and I can
load everything up into play position. I have to order a whole kit of
gears to do the repair properly. Sony # A-7040-474-C
Thanks.
Gary
J Silverman wrote:
>
> Have you checked the end sensor system and cranked through the loading
> manually to check for binding? Also look for a lever or switch that might be
> used to detect the presence of a cassette.
> Jerry Silverman
> Greentron Inc
> 4 Newland Ave
> Greenville SC 29609
> 864 232 3889
> Fax 271 2080
> mailto:greentron@xxxxxxx
> ----- Original Message -----
> From: "Gary McCartney" <gary@xxxxxxxxxxx>
> To: <techassist@xxxxxxxxxxxxx>
> Sent: Tuesday, December 03, 2002 3:01 PM
> Subject: [TechAssist] Sony VCR SLV-360, cassette goes in and come right back
> out
>
> >
> > This Sony VCR model SLV360 came into the shop with a cassette stuck
> > inside it. I had to remove the carriage in order to free the cassette. I
> > noticed that the FL-loading gear # 3-958-156-03 had some chewed teeth so
> > I ordered a new one. Now I have it all installed back together and the
> > cassette will go into the machine, all the way down to it's resting
> > position but instead of the mechanism pulling the tape out of the
> > cassette and loading it, the cassette just reverses and ejects on me. I
> > have cleaned the mode switch. Also checked the alignment of the loading
> > gears, which look ok to me although I don't have a manual to do this by.
> > for a photo of my alignment, clink on link:
> >
> >
> > http://www.number63.ca/gears.jpg
> >
> >
> > I cleaned the grease off the slide plate "rack" gear teeth and they look
> > as I believe they should. The first tooth is only half as high as the
> > rest but it looks like it was manufacturerd that way, not as if it looks
> > broken.
> >
> >
> > To see picture of teeth on slide plate, click on link:
> >
> > http://www.number63.ca/deck.jpg
> >
> >
> > I removed the loading motor so I could spin the gears manually and after
> > the cassette loading is complete, the gears lock up and won't allow the
> > tape loading procedure to start. It appears as though it's the fault of
> > the FL loading gear which I replaced because as the large black gear
> > rotates, the FL gear's flanges hit the teeth on the black gear and
> > prevent any further rotation. Still, I'm sure the FL gear is in proper
> > position.
> >
> >
> > I'm stuck on this one, any help appreciated.
> > --
> >
> >
> >
> >
> > Gary McCartney
> >
> > McCartney Electronics
> > 7134 Fife Rd, RR 7
> > Guelph Ontario Canada N1H 6J4
> > Fax: (519)821-1530
> > email: gary (at) number63.ca
> >
> > ------------------------------------------
> > To REMOVE your email address, click here:
> > http://www.tech-assist.org/unsubb.html
> > To CHANGE your email address, click here:
> > http://www.techassist.net/forms/change.html
> > ------------------------------------------
> > ***NEW*** Tips Added Instantly!!!***
> > Submit Repair Tips here:
> > http://www.tech-assist.org/secure/tip/
> >
>
> ------------------------------------------
> To REMOVE your email address, click here:
> http://www.tech-assist.org/unsubb.html
> To CHANGE your email address, click here:
> http://www.techassist.net/forms/change.html
> ------------------------------------------
> ***NEW*** Tips Added Instantly!!!***
> Submit Repair Tips here:
> http://www.tech-assist.org/secure/tip/
--
Gary McCartney
McCartney Electronics
7134 Fife Rd, RR 7
Guelph Ontario Canada N1H 6J4
Fax: (519)821-1530
email: gary (at) number63.ca
------------------------------------------
To REMOVE your email address, click here:
http://www.tech-assist.org/unsubb.html
To CHANGE your email address, click here:
http://www.techassist.net/forms/change.html
------------------------------------------
***NEW*** Tips Added Instantly!!!***
Submit Repair Tips here:
http://www.tech-assist.org/secure/tip/
Other related posts:
