Last time I called them, got a message saying closed till Jan 15. Jerry Silverman Greentron Inc 4 Newland Ave Greenville SC 29609 864 232 3889 Fax 271 2080 mailto:greentron@xxxxxxx ----- Original Message ----- From: "Kerry & Cherie" <alterego@xxxxxxxxxxx> To: <techassist@xxxxxxxxxxxxx> Sent: Thursday, January 10, 2002 8:55 PM Subject: [TechAssist] Fw: Re: Sylvannia(Funai) SRT2027 dead > > Jerry, thanks for the reply, The res's have > 20 volts on the supply side but the chip appears > dead so perhaps the supply did cause it? > any way I'll try Funai tech support possibly if > there is a phne # avail? Thanks again...Kerry > > -----Original Message----- > From: J Silverman <greentron@xxxxxxxxxxxxxxxx> > To: techassist@xxxxxxxxxxxxx <techassist@xxxxxxxxxxxxx> > Date: Thursday, January 10, 2002 5:28 PM > Subject: [TechAssist] Re: Sylvannia(Funai) SRT2027 dead > > > > > >Sounds similar to one I had about a year ago. The resistors were burned up, > >220 ohms I think. The solder on the 9 volt zener was crystalized from the > >heat. The resistors were fed from a rectifier off the SMPS secondary. There > >was also a 30 volt zener from the rectifier to ground. The 30 volt zener > was > >shorted so I had no voltage to the resistors. Funai T/A said I would > >probably have to replace the IC too. But in this unit replacing the 30 volt > >zener and the burned resistors was all that was necessary. > >Funai T/A knew right away what the damage was so it must be common. It was > >warranty so I ordered all the parts they suggested but the IC never came > in. > >Perhaps they have them in stock by now. Cause of the problem was SMPS > >runaway. Could not find anything wrong with the SMPS. > >Jerry Silverman > >Greentron Inc > >4 Newland Ave > >Greenville SC 29609 > >864 232 3889 > >Fax 271 2080 > >mailto:greentron@xxxxxxx > >----- Original Message ----- > >From: "Kerry & Cherie" <alterego@xxxxxxxxxxx> > >To: <techassist@xxxxxxxxxxxxx> > >Sent: Thursday, January 10, 2002 7:36 PM > >Subject: [TechAssist] Sylvannia(Funai) SRT2027 dead > > > > > >> I have a 27" Sylvannia(Funai) STR2027 > >> came in dead,no obvious shorts(horz out,etc). > >> relay clicks,has 105 volts on horiz output, > >> no horiz drive signal from IC301. > >> R396 & R397 very discolored and D396(zener) > >> also warm and discolored.Has 8.6volts on it, > >> I assume b+ for IC301(M61203c).I,m thinking > >> maybe this IC is bad? any one have any experience > >> on these sets? 2000 model.I don't have the service > >> manual ...Any help would be qppreciated! Thanks, > >> Kerry,KER-TEK TV, Medford Or. > >> > >> ------------------------------------------ > >> Help make your TechAssist database better! > >> Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > >> ------------------------------------------ > >> To UNSUBSCRIBE your email address, click here: > >> mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >> Or send a BLANK email with unsubscribe in the > >> SUBJECT field to the address above. > >> > >> > > > >------------------------------------------ > >Help make your TechAssist database better! > >Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > >------------------------------------------ > >To UNSUBSCRIBE your email address, click here: > >mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > >Or send a BLANK email with unsubscribe in the > >SUBJECT field to the address above. > > > > ------------------------------------------ > Help make your TechAssist database better! > Submit your fixes here: http://circuitwork.com/techassist/tip/#tips > ------------------------------------------ > To UNSUBSCRIBE your email address, click here: > mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe > Or send a BLANK email with unsubscribe in the > SUBJECT field to the address above. > > ------------------------------------------ Help make your TechAssist database better! Submit your fixes here: http://circuitwork.com/techassist/tip/#tips ------------------------------------------ To UNSUBSCRIBE your email address, click here: mailto:techassist-request@xxxxxxxxxxxxx?subject=unsubscribe Or send a BLANK email with unsubscribe in the SUBJECT field to the address above.