The Demons are HED!!!!
On Apr 10, 2018, at 04:36 PM, James Dougherty <jafrado@xxxxxxxxx> wrote:
yep. All my sweet rockets are HED :-)
On Tue, Apr 10, 2018 at 3:36 PM, Chris Attebery <chrisattebery1971@xxxxxxxxx>
wrote:
Isn't this kit set up for HED? I've built a couple HED rockets and IMHO they
work really well if you build them as designed. You don't need no stinkin'
AARD, chute release, or cable cutter.
If you're using a altimeter with a tracker you can put the antenna in an RC car
antenna tube and run it along the side of the main in the nose cone.
Here's a thread with the method I've followed:
http://www.rocketryforum.com/showthread.php?120615-CJ-s-quot-PUNISHER-quot-build
On Tue, Apr 10, 2018 at 3:17 PM <srkendal@xxxxxxxxxxx> wrote:
I used an ARRD before, and it worked perfectly. Then I bought the second
generation, and it let go early on me.
But the original was awesome.
Steve
Sent from XFINITY Connect Application
-----Original Message-----
From: jafrado@xxxxxxxxx
To: tccrockets@xxxxxxxxxxxxx
Cc: srkendal@xxxxxxxxxxx
Sent: 2018-04-10 3:12:53 PM
Subject: Re: [tccrockets] Re: [roc-chat] Re: Re: LDRS37 Kit Special Available!
So the ARRD I have used before, I also used the breakwire thing jimmy turned me
onto - don't remember what it is called, in my garage.
I'm thinking 20' of kevlar, and this mylar streamer all wrapped up in a
Nomex...https://www.homedepot.com/p/Bird-B-Gone-Holographic-Flash-Tape-Bird-Deterrent-150-ft-x-2-in-MMAFT-SIL/206044654
Imagine that thing re-entering from 5-10K :-)
Anyhow, cheap and easy fast up and down.
You know we have a points system for this race :-)
On Tue, Apr 10, 2018 at 2:59 PM, fetchen <fetchen@xxxxxxxxx> wrote:
Yes, reliability is my biggest concern using a tether device. My thought is to
use multi-strand wire from the ebay to the tether device taped to the shock
cord, and then solder and heat shrink the e-match leads to the multi-strand
wire where they will not flex. I plan on using a deployment bag to minimize
flapping – but it is still going to flap no matter what.
I also looked at the Jolley Logic Chute Release, as it is all self-contained.
But it looks a little small for this application. It uses a rubber bands to
wrap the chute, and does not look like it would work in a configuration where a
drogue is deployed first, which then pulls the deployment bag off when the
tether is released to deploy the main.
Anyone with experience with this vs a traditional tether device?
Tom Fetter
From: srkendal@xxxxxxxxxxx <srkendal@xxxxxxxxxxx>
Sent: Tuesday, April 10, 2018 1:16 PM
To: fetchen@xxxxxxxxx
Subject: Re: [tccrockets] Re: [roc-chat] Re: Re: LDRS37 Kit Special Available!
Hi Tom,
I have something that came from Defy Gravity. I don't remember what it was
called. It uses an e-match to separate two haves that hold cable loops.
My concern is that this piece of machined aluminum and my parachute are flapping in the breeze with an attached piece of e-match wire. I've had it break before. Even if you tape it up to the shock cord with stain reliefs, that solid core wire can break from excessive flexures.
How do you keep it together and reliable?
Thanks!
Steve
Sent from XFINITY Connect Application
-----Original Message-----
From: fetchen@xxxxxxxxx
To: tccrockets@xxxxxxxxxxxxx
Sent: 2018-04-10 12:45:19 PM
Subject: [tccrockets] Re: [roc-chat] Re: Re: LDRS37 Kit Special Available!
I am plan on deploying both the drogue and main out of the main body, using a
Tender Descender (never used one before) to release the main. The method Mike
Stoop describes sounds very interesting – one of those “I never would have
thought of doing it that way” – but I like to reserve the nosecone space for
my Beeline GPS and other flight tracking electronics. Using the main body for
both main and drogue, I can definitely fit a 54mm K550, and maybe even a K700 –
or maybe not. I am using an Aero Pack 54mm-3” conical motor retainer, so that
moves the motor a little aft, and I plan on shortening the eBay tube from 7” to
5 or 6”, which will give a little more space for motor and chutes.
Tom Fetter
From: tccrockets-bounce@xxxxxxxxxxxxx <tccrockets-bounce@xxxxxxxxxxxxx> On
Behalf Of srkendal@xxxxxxxxxxx
Sent: Tuesday, April 10, 2018 9:57 AM
To: gary-walker@xxxxxxxxxxx; tccrockets@xxxxxxxxxxxxx; kf6jbg@xxxxxxx
Subject: [tccrockets] Re: [roc-chat] Re: Re: LDRS37 Kit Special Available!
I used some (previously used) lacquer thinner, which contains acetone. But it
was a later choice. Perhaps the oils I used (mineral spirits, WD-40) inhibited
it somewhat. I ultimately used a card scraper and that WD-40. It worked. But as
mentioned, I had to further scrub the crap out of them to get all THAT off.
In the end, they look great, but as also mentioned, I intend to do a carbon fiber lay up, so they're getting totally scuffed up anyway before I do that.
BTW, it was pretty hard to get that stack of fins apart initially. No match for my
1" chisel, but still. But I guess they need to keep them together to rout them
out. (I assume they use a CNC router to cut them out.)
The rest of the kit is fine. I did have to open the fin slots just a bit (much
too tight) but that's typical.
I do have a question for the list: if attempting to do dual deployment, is anyone attempting to pack the main in the nose cone? Or are you planning to use something like a jolly logic chute release and pop it all out at the top? There looks to be enough room in the N/C for a main, but it will be a fairly tight fit. Plus, I'll need to replace the screw holding the tip on the N/C with an eye-bolt.
Just wondering if you were expecting to simply chase it down or try to bring it
down dual.
Thanks.
Steve
Sent from XFINITY Connect Application
-----Original Message-----
From: gary-walker@xxxxxxxxxxx
To: tccrockets@xxxxxxxxxxxxx, kf6jbg@xxxxxxx, srkendal@xxxxxxxxxxx
Sent: 2018-04-10 8:32:07 AM
Subject: [tccrockets] Re: [roc-chat] Re: Re: LDRS37 Kit Special Available!
Acetone does a clean fairly quick removal after it softens.
Gary W
I see you haven't yet gotten the gunk (tape residue?) off your fins.
It took me over an hour to clean it all off. I tried a bunch of things to try to clean it off including Goo-Gone, IPA, Mineral spirits and lacquer thinner. The only thing I found that even kind of cut it was WD-40. Still had to use some Scottch Bright to get some of it off. Of course then I had to scrub them all with Dawn and rinse them in IPA.
But they look pretty and clean now. Too bad I'm going to scuff then up, put a
couple layers of CF over them, and stuff them in a vacuum bag. But hey, no
lumps. :-)
Steve
Sent from XFINITY Connect Application
-----Original Message-----
From: kf6jbg@xxxxxxx
To: tccrockets@xxxxxxxxxxxxx
Sent: 2018-04-09 10:17:08 PM
Subject: [tccrockets] Re: [roc-chat] Re: Re: LDRS37 Kit Special Available!
Gary Walker
Tripoli Central CA
TRA # 9273 - L3
On April 9, 2018 at 10:28 PM srkendal@xxxxxxxxxxx wrote:
Here is a photo with motor tube installed. The fins need to be ground down to
fit into slots. Having a grinder with a flappy type grinding disk sure helped
in getting it to fit the slots. It got dark so I could not take a photo of the
fins installed. I only got 9 out of 12 fillets epoxied inside the body to motor
tube/fins today. Larry Taylor
Sent from Mail for Windows 10
From: James Dougherty
Sent: Tuesday, March 27, 2018 12:03 AM
To: ROC Chat
Cc: TCC chat; Richard King; aeropac@xxxxxxxxxxxxx
Subject: [tccrockets] Re: [roc-chat] Re: Re: LDRS37 Kit Special Available!
Yeah, I wish. Too short a burn. My Little dog is almost the same rocket and it
barely touchs 3400' AGL with that load :(
Thats a painted finish (2K urethane). At least, it was :-)
On Mon, Mar 26, 2018 at 11:55 PM, Ron McGough <rrmagoo7@xxxxxxxxxxx> wrote:
Hey James,
I think that you forgot a "0" after the "3". I think the K2045 has a little
more oomph than 3K in a 6 pound rocket. Lol
Ron McGough
Sent from my Galaxy Tab A
-------- Original message --------
From: James Dougherty <jafrado@xxxxxxxxx>
Date: 3/26/18 11:16 PM (GMT-08:00)
To: TCC chat <tccrockets@xxxxxxxxxxxxx>
Cc: Richard King <drrbk@xxxxxxxxxxx>, ROC Chat <roc-chat@xxxxxxxxxxxxx>,
aeropac@xxxxxxxxxxxxx
Subject: [roc-chat] Re: [tccrockets] Re: LDRS37 Kit Special Available!
Here's the RASAero and Rocksim files.
It's about a 6lb rocket loaded with a K2045 and will do about 3K.
CP is optimal at 30" from the nose. It will need about 4 oz of mass up front;
I plan to put electronics (MARSA) and some Lipos up there.
I'm thinking 40' mylar streamer drogue.
On Thu, Mar 15, 2018 at 4:34 AM, JAMES FRANCO <ALDOCYBER3@xxxxxxx> wrote:
Got my decal… don’t know what I am going to put it on. LOL
Get them while you can guys and gals, there is only going to be one LDRS 37 TCC
Jimmy F.
Tripoli Rocketry Association
Member 12524
Level 3
From: tccrockets-bounce@xxxxxxxxxxxxx [mailto:tccrockets-bounce@xxxxxxxxxxxxx] ;
On Behalf Of James Dougherty
Sent: Wednesday, March 14, 2018 6:53 PM
To: TCC chat <tccrockets@xxxxxxxxxxxxx>
Cc: Richard King <drrbk@xxxxxxxxxxx>; ROC Chat <roc-chat@xxxxxxxxxxxxx>;
aeropac@xxxxxxxxxxxxx
Subject: [tccrockets] Re: LDRS37 Kit Special Available!
Decal available here - http://stickershock23.com/product/ldrs-xxxvii/
Still more available, get them while you can - this is a great deal!
On Wed, Mar 14, 2018 at 3:00 PM, James Dougherty <jafrado@xxxxxxxxx> wrote:
OMG - you and Motta need to have a party :-)
Mike told me that the pallet from Curtis is on it's way and he's getting the
nosecone tips next; should ship soon! More on this later ...
On Wed, Mar 14, 2018 at 1:52 PM, aaron hagadorn <hagadornclassics@xxxxxxxxx>
wrote:
Have not got mine yet but that's a good thing my rocket build room/ammo
reloading/Aaron's getaway room almost went up in flames. Work out of town for
month and the wiring in the walls shorts out. Go figure now it's repair wiring
and build rockets
Aaron Hagadorn
On Mar 13, 2018 10:14 PM, <srkendal@xxxxxxxxxxx> wrote:
My order says "Awaiting fulfillment".
Steve
Sent from XFINITY Connect Application
-----Original Message-----
From: drrbk@xxxxxxxxxxx
To: tccrockets@xxxxxxxxxxxxx, roc-chat@xxxxxxxxxxxxx, aeropac@xxxxxxxxxxxxx
Sent: 2018-03-13 9:21:30 PM
Subject: [tccrockets] Re: LDRS37 Kit Special Available!
Anyone received theirs?
RK
From: James Dougherty
Sent: Wednesday, February 28, 2018 9:11 PM
To: TCC chat ; ROC Chat ; aeropac@xxxxxxxxxxxxx
Subject: [tccrockets] LDRS37 Kit Special Available!
Hi Folks,
LDRS37 Kit special - the Avalanche from Madcow Rocketry!
Only 100 of these kits are available so order now!
https://www.madcowrocketry.com/3-avalanche
Thank you!
-James
Virus-free. www.avast.com
