Hi, Well basically is a segmentation fault with the 3d cns godunov solver, I'm trying to see if I can solve the problem by myself but is not likely probable. Regards, Joel ----- Original Message ---- From: Bill Henshaw <henshaw@xxxxxxxx> To: overture@xxxxxxxxxxxxx Sent: Friday, February 6, 2009 6:46:28 PM Subject: [overture] Re: 3d cns Joel, I have forgotten what the problem was with the Godunov solver but I will look at putting an intermediate version of Overture, v22n, on the web site. This will likely take a few days. ...Bill Joel Guerrero wrote: > Hi Bill, > > I wonder if there is a patch ready for the godunov version of cns solver. > For the moment I'm using the jameson solver which runs fine, but I cannot use > AMR. > > > Cheers, > > Joel > > > > ----- Original Message ---- > From: Bill Henshaw <henshaw@xxxxxxxx> > To: overture@xxxxxxxxxxxxx > Sent: Monday, December 15, 2008 7:09:45 PM > Subject: [overture] Re: 3d cns > > Hi Joel, > We have been running quite a few 3D cns cases. I know we > have fixed some issues with 3d parallel AMR. It must be > that there are some bugs in your version. Hopefully I will > be able to put out a new version sometime soon. > > Regards, > Bill. > > Joel Guerrero wrote: >> By the way, >> >> I'm getting the same segmentation error for all cns 3d cases. It is fully >> working the 3d version of the cns solver? >> >> Joel >> >> >> ----- Original Message ---- >> From: Joel Guerrero <joegi.geo@xxxxxxxxx> >> To: overture@xxxxxxxxxxxxx >> Sent: Sunday, December 14, 2008 10:08:59 PM >> Subject: [overture] 3d cns >> >> Hi, I'm trying to run a 3d case using cns but I-m getting this error. >> >> 0.000e+00 gamma=1.400e+00 >> a=1.00e+00, b=0.00e+00, c=0.00e+00, d=2.50e-01, stepPosition = 2.500000e-01, >> stepSharpness=0.000000e+00 uLeft = >> [2.667e+00,1.250e+00,0.000e+00,0.000e+00,1.205e+00,] >> uRight = [1.000e+00,0.000e+00,0.000e+00,0.000e+00,7.144e-01,] >> assignIC: step function: grid=0 stepNormal=( 1.00e+00, 0.00e+00, 0.00e+00), >> stepNormalEquationValue= 2.50e-01 >> continue >> debug >> 1 7 31 >> debug=1 >> continue >> ---assigning reynoldsNumber to match mu---- >> ---assigning machNumber to match Rg---- >> inside DomainSolver::setup >> DomainSolver::initialize: numberOfGridFunctionsToUse= 2, >> numberOfExtraFunctionsToUse=1 +++++DomainSolver::initialize: >> cg.numberOfComponentGrids=1 ++++++++++++++ >> **** Build AMR levels for the initial conditions... ***** >> interpolateAndApplyBoundaryConditions (start) steps=-1 t=0: number of array >> ID's has increased to 498 >> Overture::checkMemoryUsage: interpolateAndApplyBoundaryConditions (start) >> steps=-1 t=0, myid=0: memory usage has increased to 21.1523 (Mb) >> *****Build AMR level = 1 Segmentation fault >> >> >> I get this error trying to run the shockTube3d.cmd testcase included in the >> cg distributuion, any idea what could be the error? >> >> >> Regards, >> >> Joel >> >> >> >> > > > > >