[PCB_FORUM] Re: RE : Re: Need Help with Error in Text LingOrigin!
- From: "Bolman, Shirley H" <shirley.h.bolman@xxxxxxxxx>
- To: <icu-pcb-forum@xxxxxxxxxxxxx>
- Date: Wed, 24 May 2006 18:34:24 -0700
Have you tried the Setup>Text Sizes form in allegro to see if one of them is
set very large?
Normally only 3 or 4 text block sizes are really used and sometimes the wrong
info can be
used when a physical is created. For instance my Text Block 1 has a height of
25 mils with a width of 16 mils.
If the height were changed to 250 mils instead then it may cause the problems
you are seeing.
The other suggestion of changing the Setup>Drawing Parameters to a size larger
than the xy
coordinate in your error should allow you to find the culprit and fix it.
Shirley in Oregon
________________________________
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx] On Behalf Of richard moffat
Sent: Wednesday, May 24, 2006 5:40 PM
To: icu-pcb-forum@xxxxxxxxxxxxx
Subject: [PCB_FORUM] Re: RE : Re: Need Help with Error in Text LingOrigin!
LMAO. That's a sort of response I'd expect from a production engineer or
design engineer!
>>> sjchar3@xxxxxxxxxxxx 25/05/2006 10:38:48 a.m. >>>
can't you just shrink all the text in text editor?
-----Original Message-----
From: Jean-Charles TEYSSIER <jcteyssier@xxxxxxxxxxxxxxx>
To: icu-pcb-forum@xxxxxxxxxxxxx
Sent: Wed, 24 May 2006 22:19:39 +0200
Subject: [PCB_FORUM] RE : Re: Need Help with Error in Text Ling Origin!
Yes it sound like something i saw in the past:
a text becomes to large and a part of it is out of extents...
Appears after a refresh symbol with presere text block enable.
Jean-Charles TEYSSIER
Icra Industrie
-------- Message d'origine--------
De: icu-pcb-forum-bounce@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-bounce%40freelists.org> de la part de Handley, William
Date: mer. 24/05/2006 21:52
À: icu-pcb-forum@xxxxxxxxxxxxx <mailto:icu-pcb-forum%40freelists.org>
Objet : [PCB_FORUM] Re: Need Help with Error in Text Ling Origin!
Henry? Who is Henry?
GO to set-up > drawing size, and make the drawing extents width and height much
larger than the x,y coord you have in the error.
Bill, not henry
p.s. this only works if you name the database Billy.brd
-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-bounce%40freelists.org>
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-bounce%40freelists.org> ]
On Behalf Of Judy Huang
Sent: Wednesday, May 24, 2006 11:36 AM
To: icu-pcb-forum@xxxxxxxxxxxxx <mailto:icu-pcb-forum%40freelists.org>
Subject: [PCB_FORUM] Re: Need Help with Error in Text Ling Origin!
Hi Henry,
Can you please tell me the commands to "expand the database"?
Regards,
Judy Huang
ATE Resources, Inc.
Mobile: 0933468325
Office: 03-5516680 Ext. 325
Fax: 03-5587916
----- Original Message -----
From: "Handley, William" <william.handley@xxxxxxxxx
<mailto:william.handley%40intel.com> >
To: <icu-pcb-forum@xxxxxxxxxxxxx <mailto:icu-pcb-forum%40freelists.org> >
Cc: <judyh@xxxxxxxxxx <mailto:judyh%40atests.com> >
Sent: Thursday, May 25, 2006 1:21 AM
Subject: [PCB_FORUM] Re: Need Help with Error in Text Ling Origin!
Expand the database, (copy it to the name Billy, that always works for me.)
Show element (be sure to turn on the layer BRD geo, silkscreen) at x
6425.000 -544995.912.
Find the offending comp. go back to your original database, delete the comp
and bring it back in. Sounds like there is a text size difference between
the symbol and database you may want to check the sym and database txt
sizes. i.e. txt size 4 is 35 mil in the symbol, and 250 in the database.
Bill
Bill Handley CID+
Sr. CAD eng.
Intel Corp. DEG/CIG/IPD/CE/PEG?
5000 W. Chandler Blvd.
MS C6- 450
Chandler, Az 85226
william.handley@xxxxxxxxx <mailto:william.handley%40intel.com>
(480) 554-9673 Fax. (480)554 7674
-----Original Message-----
From: icu-pcb-forum-bounce@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-bounce%40freelists.org>
[mailto:icu-pcb-forum-bounce@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-bounce%40freelists.org> ] On Behalf Of judyh@xxxxxxxxxx
<mailto:judyh%40atests.com>
Sent: Wednesday, May 24, 2006 10:10 AM
To: icu-pcb-forum@xxxxxxxxxxxxx <mailto:icu-pcb-forum%40freelists.org> ;
J-Charles TEYSSIER
Subject: [PCB_FORUM] Re: Need Help with Error in Text Ling Origin!
Hi Jean,
Already done that. Still didn't work. Are there any other ways to fix it?
Regards,
Judy Huang
Quoting J-Charles TEYSSIER <jcteyssier@xxxxxxxxxxxxxxx
<mailto:jcteyssier%40groupe-icra.com> >:
> Try tu run dbdoctor on your database.
>
> It sound like a corrupted database.
>
> Jean-Charles TEYSSIER
>
> Judy Huang a écrit :
>
>> Hi All,
>>
>> I have encountered the following error message while generating
>> gerber files:
>>
>> ERROR IN TEXT LINE origin = (6425.000 -544995.912)
>> class = BOARD GEOMETRY
>> subclass = SILKSCREEN_BOTTOM
>> TEXT LINE OUT OF EXTENTS
>> Error cannot be fixed.
>> ERROR INVALID SECTOR ROW
>> Error cannot be fixed.
>> Regenerating DRC
>> 0 original DRC errors replaced by
>> 0 current DRC errors.
>> 0 warnings, 2 errors detected, 0 errors fixed.
>>
>>
>> Seems (6425.000 -544995.912) is out of range (on my page), can
>> someone teach me how to solve this issue? I'm thinking about using
>> Techfile, Sub-Drawings (excluding the Silkscreen Bottom, which seems
>> to be where the issue is) and regenerate the layout file on a new
>> design. Does anyone know if this will work? Or is there any other
>> way of doing it?
>>
>> Any help will be appreciated. Thanks all!
>>
>> Regards,
>>
>> Judy Huang
>> ATE Resources, Inc.
>> Mobile: 0933468325
>> Office: 03-5516680 Ext. 325
>> Fax: 03-5587916
>>
>> -----------------------------------------------------------
>> To subscribe/unsubscribe: Send a message to
>> icu-pcb-forum-request@xxxxxxxxxxxxx
>> <mailto:icu-pcb-forum-request%40freelists.org>
>> with a subject of subscribe or unsubscribe
>>
>> To view the archives of this list go to
>> //www.freelists.org/archives/icu-pcb-forum/
>>
>> Problems or Questions:
>> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
>> <mailto:icu-pcb-forum-admins%40freelists.org>
>> -----------------------------------------------------------
>>
> -----------------------------------------------------------
> To subscribe/unsubscribe: Send a message to
> icu-pcb-forum-request@xxxxxxxxxxxxx
> <mailto:icu-pcb-forum-request%40freelists.org>
> with a subject of subscribe or unsubscribe
>
> To view the archives of this list go to
> //www.freelists.org/archives/icu-pcb-forum/
>
> Problems or Questions:
> Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
> <mailto:icu-pcb-forum-admins%40freelists.org>
> -----------------------------------------------------------
>
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-request%40freelists.org>
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-admins%40freelists.org>
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-request%40freelists.org>
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-admins%40freelists.org>
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-request%40freelists.org>
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-admins%40freelists.org>
-----------------------------------------------------------
-----------------------------------------------------------
To subscribe/unsubscribe:
Send a message to icu-pcb-forum-request@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-request%40freelists.org>
with a subject of subscribe or unsubscribe
To view the archives of this list go to
//www.freelists.org/archives/icu-pcb-forum/
Problems or Questions:
Send an email to icu-pcb-forum-admins@xxxxxxxxxxxxx
<mailto:icu-pcb-forum-admins%40freelists.org>
-----------------------------------------------------------
________________________________
Try the New Netscape Mail Today!
Virtually Spam-Free | More Storage | Import Your Contact List
http://mail.netscape.com
NOTICE: This message contains privileged and confidential
information intended only for the use of the addressee
named above. If you are not the intended recipient of
this message you are hereby notified that you must not
disseminate, copy or take any action in reliance on it.
If you have received this message in error please
notify Allied Telesis Labs Ltd immediately.
Any views expressed in this message are those of the
individual sender, except where the sender has the
authority to issue and specifically states them to
be the views of Allied Telesis Labs.
Other related posts:
- » [PCB_FORUM] Re: RE : Re: Need Help with Error in Text LingOrigin!
