Re: [foxboro] FCM/CP Insertion
- From: "Boulay, Russ" <Russ.Boulay@xxxxxxxxxxxx>
- To: "'foxboro@xxxxxxxxxxxxx'" <foxboro@xxxxxxxxxxxxx>
- Date: Fri, 2 Dec 2011 12:55:31 -0500
There is the one additional caveat with the ZCP. The FT connector is supposed
to get installed on the Shadow module prior to inserting into cell bus. This
way as module recives power it also engages the primary module. Without the ft
connector no cables should be on Shadow as it would be perceived as a single
primary module.
--------------------------
Sent using BlackBerry
----- Original Message -----
From: William C Ricker [mailto:wcricker@xxxxxxxxxxxxxxx]
Sent: Friday, December 02, 2011 12:47 PM
To: foxboro@xxxxxxxxxxxxx <foxboro@xxxxxxxxxxxxx>
Subject: Re: [foxboro] FCM/CP Insertion
Thanks, Russ.
William C Ricker
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On
Behalf Of Boulay, Russ
Sent: Friday, December 02, 2011 12:37 PM
To: foxboro@xxxxxxxxxxxxx
Subject: Re: [foxboro] FCM/CP Insertion
ZCPs have extra cables (I/O) which are elevator related and cannot be
installed prior to installing the module...
FCP's do not have such cables.
In both module cases, pre connection of cables is viable if it is the
Shadow.
However if you are just plugging a FCP or ZCP into a system as the Primary
module then caution should be taken to not attach cables unless you
absolutely know it's personality that is resident in memory...
So in the Primary case...no cables...letterbug reader...etc....
-----Original Message-----
From: foxboro-bounce@xxxxxxxxxxxxx [mailto:foxboro-bounce@xxxxxxxxxxxxx] On
Behalf Of William C Ricker
Sent: Friday, December 02, 2011 9:29 AM
To: foxboro@xxxxxxxxxxxxx
Subject: [foxboro] FCM/CP Insertion
( I'll try Again )
A dilemma
Both v8.5 and 8.6 release notes clearly say that when adding the second of a
fault
tolerant pair of CP or FCM,
1 Connect the cables to the station
2 Insert the module with it's partner
In the ZCP User Guide it specifically says not to disconnect the cables, put
the
module in, then wait for specific operation of the LEDs, and only then
connect the
cables. (It then specifies which screw to tighten first.)
In the FCP User Guide, it specifically says to connect the cables first,
then put
the module onto the baseplate next to the partner, tighten the screws and
observe
that it marries.
I haven't yet found a book which specifies the FCM startup sequence.
So, if I have a ZCP, do I use the User Guide method or the Release Notes
method?
Any insight?
Regards,
William C Ricker
FeedForward, Inc.
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
*** Confidentiality Notice: This e-mail, including any associated or
attached files, is intended solely for the individual or entity to which it
is addressed. This e-mail is confidential and may well also be legally
privileged. If you have received it in error, you are on notice of its
status. Please notify the sender immediately by reply e-mail and then delete
this message from your system. Please do not copy it or use it for any
purposes, or disclose its contents to any other person. This email comes
from a division of the Invensys Group, owned by Invensys plc, which is a
company registered in England and Wales with its registered office at 3rd
Floor, 40 Grosvenor Place, London, SW1X 7AW (Registered number 166023). For
a list of European legal entities within the Invensys Group, please go to
http://www.invensys.com/en/legal/default.aspx.
You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail
reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be
subject to the terms of any agreements between Invensys (and/or its
subsidiaries and affiliates) and the recipient (and/or its subsidiaries and
affiliates).
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
*** Confidentiality Notice: This e-mail, including any associated or attached
files, is intended solely for the individual or entity to which it is
addressed. This e-mail is confidential and may well also be legally privileged.
If you have received it in error, you are on notice of its status. Please
notify the sender immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or disclose its
contents to any other person. This email comes from a division of the Invensys
Group, owned by Invensys plc, which is a company registered in England and
Wales with its registered office at 3rd Floor, 40 Grosvenor Place, London, SW1X
7AW (Registered number 166023). For a list of European legal entities within
the Invensys Group, please go to http://www.invensys.com/en/legal/default.aspx.
You may contact Invensys plc on +44 (0)20 3155 1200 or e-mail
reception@xxxxxxxxxxxxx This e-mail and any attachments thereto may be subject
to the terms of any agreements between Invensys (and/or its subsidiaries and
affiliates) and the recipient (and/or its subsidiaries and affiliates).
_______________________________________________________________________
This mailing list is neither sponsored nor endorsed by Invensys Process
Systems (formerly The Foxboro Company). Use the info you obtain here at
your own risks. Read http://www.thecassandraproject.org/disclaimer.html
foxboro mailing list: //www.freelists.org/list/foxboro
to subscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=join
to unsubscribe: mailto:foxboro-request@xxxxxxxxxxxxx?subject=leave
Other related posts:
